background image

6  Installation

6.1  Ensuring safety

Follow the instructions below for safe installation.
Warning instructions are located before a potentially dangerous task.

Disregard of warning instructions can cause serious injuries!

Complying with safety warnings

Disregard of safety notes can cause unforeseeable dangers!
➤ Follow the instructions in chapter 3 “Safety and Responsibility”.
➤ Installation work may only be carried out by authorized personnel.
➤ Make sure that no one is working on the machine.
➤ Ensure that all service doors and panels are locked.

When working on live components

Touching voltage carrying components can result in electric shocks, burns or death.
➤ Work on electrical equipment may only be carried out by authorized electricians.
➤ Switch off and lock out the power supply disconnecting device and check that no voltage is

present.

➤ Check that the floating relay contacts are voltage-free.

When working on the compressed air system

Compressed air is contained energy. Uncontrolled release of this energy can cause serious injury

or death. The following safety concerns relate to any work on components that could be under

pressure.
➤ Close shut-off valves or otherwise isolate the machine from the compressed air network to en‐

sure that no compressed air can flow back into the machine.

➤ Vent all pressurized components and enclosures.
➤ Check all hose couplings in the compressed air system with a hand-held pressure gauge to en‐

sure that they all read 0 bar.

➤ Do not open or dismantle any valves.

When working on the drive system

Touching voltage carrying components can result in electric shocks, burns or death.

Touching the fan while the machine is running can result in serious injury.
➤ Switch off and lock out the power supply disconnecting device and verify the absence of volt‐

age.

➤ Do not open the cabinet while the machine is switched on.

Further information Details of authorized personnel are found in chapter 3.4.2.

Details of dangers and their avoidance are found in chapter 3.5.

6

Installation

6.1

Ensuring safety

38

Operator Manual    Screw Compressor  
AIRTOWER 3C–7.5C Tri-Voltage

9_6917 34  USE

Содержание AIRTOWER 3C





























































































































Отзывы: