background image

FCC 

STATEMENT 

This 

device complies 

with 

Class 

limits, Part 

I 5  

of 

FCC 

rules.  See  instructions 

if 

interference to 

radio reception 

is 

suspeded. 

This equipment generates and uses radio frequency  energy and 

if 

not installed and used properly, 

in 

strict accordance 

with 

the manufacturer's instructions, 

it 

may cause interference 

to 

radio and 

television reception.  Please note that all peripherals must be attached with shielded cables to 

prevent interference.  This device has been tested and found 

to 

comply with the limits for a Class 

computing device 

in 

accordance 

with 

the specifications 

in 

Subpart 

of Part 

I 3  

of 

FCC 

Rules, 

which are designed to provide reasonable protection against such interference 

in 

a residential 

installation.  If this equipment does cause interference to radio 

or television reception, 

which 

can 

be determined by turning the equipment 

on 

and 

off, 

the user is encouraged 

to 

try 

to correct the 

interference by one 

of 

the following measures: 

I .  

Reorient the receiving antenna. 

2. 

Relocate the computer 

with 

respect 

to 

the receiver. 

3. 

Plug the computer 

into a different outlet so that the computer and receiver are on different 

branch circuits. 

4. 

If necessary, the user should consult the dealer or an experienced radio/television technician 

for 

additional suggestions. 

The user may 

find 

further information 

in 

the booklet 

How 

to 

Identify 

and 

Resolve Radio-TV 

Interference 

Problems. 

This 

booklet is prepared by the Federal Communications Commission and 

is 

available 

from 

the 

US 

Government Printing Office, Washington, 

DC  20004. 

Stock 

Number 

004-000-00345-4. 

In order 

for 

an installation of 

this 

product to maintain compliance with the limits for a Class 

device, shielded cables must be used for Connection 

of any devices external to this product. 

The 

FCC 

(with 

its 

action 

in General Docket 

79- 

144, 

March 

13, 1986) 

has adopted a safety 

standard 

for 

human exposure to radio frequency electromagnetic energy emitted by FCC 

regulated equipment.  Kachina recommends that you observe the following safety standards: 

DO NOT 

operate a fixed or mobile radio transmitter when someone is within two feet 

of 

the antenna. 

connectors are properly terminated. 

atmosphere. 

DO NOT 

operate any radio transmitter unless all 

RF 

connectors are secure and any open 

DO NOT 

operate radio equipment near electrical blasting caps or 

in 

an explosive 

DO 

NOT 

press the push-to-talk button except when you intend to transmit. 

G R O U N D  

ALL 

RADIO EQUIPMENT 

according the Kachina's installation instructions. 

Repair 

of 

KACHINA products should be performed only by KACHINA authorized 

personnel. 

Содержание 505DSP




















Отзывы: