Kaba Access manager 92 32 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 53

background image

Technical Manual

Installation

37

04045524 - 08/2016

Kaba access manager 92 32

5.7.6.3 Switching the external DC power supply to OUT1

By setting the jumper pair with designation VREL, a DC power supply connected via
the VREL terminal (max. 30 V DC, 2 A) is switched to the OUT1 output.

This variant can be used both with device power supply via PoE and device power
supply via an external 24 V DC power supply unit.

Principle of output wiring

Jumper position

IMPORTANT:

Only the jumper

pair VREL may be set. All other
jumpers may not be set.

5.7.6.4 Switching 24 V DC to OUT1

By setting the jumper pair with designation 24 V DC, the 24 V DC power supply (ter-
minal 24 V EXT) is switched to the OUT1 output. Consumers, for example door open-
ers which are operated with 24 V DC, can be directly connected to OUT1 in this way.

This variant can be used only with device power supply via an external 24 V DC
power supply unit. Not for power supply via PoE.

Principle of output wiring

Jumper position

IMPORTANT:

Only the jumper

pair 24 V DC may be set. All
other jumpers may not be set.

5.7.6.5 Connecting door openers

Closed-circuit door-openers and open-circuit door-openers can be used.

«
...
35
36
37
38
39
...
»

Содержание Access manager 92 32






















































Отзывы:

Нет отзывов

Похожие инструкции для Access manager 92 32

Бренд: Datalogic Страницы: 184

Gryphon I GD4100

Бренд: Datalogic Страницы: 28

Magellan 2200VS

Бренд: Datalogic Страницы: 388

Gryphon I GD44XX

Бренд: Datalogic Страницы: 324

Бренд: Datalogic Страницы: 304

Gryphon 2D Series

Бренд: Datalogic Страницы: 356

Бренд: Datalogic Страницы: 208

Бренд: Datalogic Страницы: 18

Бренд: Datalogic Страницы: 16

Бренд: Datalogic Страницы: 12

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 48

Compact 2D Reader Matrix-2000

Бренд: Datalogic Страницы: 11

Бренд: Datalogic Страницы: 169

Бренд: Datalogic Страницы: 72

Бренд: Datalogic Страницы: 10

Gryphon I GD4100

Бренд: Datalogic Страницы: 428

Бренд: Datalogic Страницы: 168

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды