Kaba Access manager 92 32 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 53

background image

Installation

Technical Manual

38

04045524 - 08/2016

Kaba access manager 92 32

For door openers that are supplied with DC voltage, a diode (a freewheeling diode)
must be connected in parallel to the door opener to suppress interference. In doing
so, make sure that the diode is connected in reverse-bias direction and check the po-
larity of the connected voltage.

When using an alternating voltage power supply, a varistor or a bipolar suppressor
diode must be connected in parallel. As regards the dimensioning and type, observe
the specifications of the door opener manufacturer.

The diode or varistor must be connected directly to the door opener and may not be
fitted to the access manager.

This step is not required if a door opener with internal varistor or diode is used.

1

Door-opener

2

Freewheeling diode or varistor

«
...
36
37
38
39
40
...
»

Содержание Access manager 92 32






















































Отзывы:

Нет отзывов

Похожие инструкции для Access manager 92 32

Бренд: Black Box Страницы: 27

Бренд: Netum Страницы: 17

Бренд: Renkforce Страницы: 2

Бренд: HID Страницы: 2

Бренд: Infinite Peripherals Страницы: 4

Бренд: Caliber Страницы: 20

Бренд: Kobil Страницы: 3

Бренд: Samsung Страницы: 36

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 3

Бренд: Sony Страницы: 242

Бренд: Sony Страницы: 263

Бренд: Broadcom Страницы: 16

Бренд: Broadcom Страницы: 18

CDX-F7705X Operating Instructions (English

Бренд: Sony Страницы: 4

CDX-F7710 Operating Instructions (English

Бренд: Sony Страницы: 40

CDX-F605X - Fm/am Compact Disc Player

Бренд: Sony Страницы: 40

CDX-F5710 - Fm/am Compact Disc Player

Бренд: Sony Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды