Kaba Access manager 92 32 Скачать руководство пользователя страница 21

Страница: 21 / 53

Technical Manual

Design and function

04045524 - 08/2016

Kaba access manager 92 32

4.10.1

Device status

The status of the device is indicated by the LED labeled

State

Signaling depends on the terminal software used.

4.10.1.1 Connection establishment

The terminal software EX-AM xx.xx.xx indicates various states and processes via the
LEDs "Device status" and "exivo network".

"Device status" LED

After starting the device, the system performs several steps until it is ready for use.
They are indicated by means of the "Device status" LED as follows:

Signal

Meaning

Yellow (approx. xx sec.)

The operating system is started

Flashing in yellow (approx. xx sec.)

Waits for possible key actuation (cold
start)

Red (approx. xx sec.)

Waits for possible key actuation (default
IP)

Green, then flashing in green

The terminal software is started

Status and error states after system start

Signal

Meaning

Green

Terminal software was started success-
fully

Red/flashing in green

1-click installation active

The device is waiting for registration by
the Internet platform

Flashing in yellow

Terminal software was not started

Flashing in red

Terminal software could not be started

Reason:

"exivo network" LED

Signal

Meaning

Lit in red

No connection with the exivo platform

Flashing in yellow

Connection with the exivo platform has
been established

Blinking in green

The device has been assigned to a sys-
tem

Lit in green

The device has been successfully as-
signed to a door

Содержание Access manager 92 32






















































Результаты поиска

Содержание Access manager 92 32

Отзывы:

Похожие инструкции для Access manager 92 32

Бренды по названию

Популярные бренды

Kaba Access manager 92 32, Техническое руководство

Результаты поиска

Содержание Access manager 92 32

Отзывы:

Похожие инструкции для Access manager 92 32

Бренды по названию

Популярные бренды