background image

7

Unlock the Lock - Lock User Pre-Set

1.

Enter the default factory access combination of 

5525

 for the Lock User.

If the combination is entered successfully, the lock displays one green flash 

G

with a beep 

  to indicate that a valid combination has been entered. One long

green flash 

G

 displays with a beep 

 to indicate that the motor has fired and

the lock is in the “unlocked” state.

Note:

A “lock open” audit record is written at this point.

2.

Turn the lock knob clockwise (CW) to the “unlocked” position to open the
secured unit (cabinet, cart, drawer, etc.)

Practice locking and unlocking the lock several times with the pre-set combination
before setting a new combination. To set a new lock user combination, see the
section in this manual on Lock User Operations or you can refer to the Unicon CL10
Lock User Operations (P/N # 3111.017).

Lock Setup

The lock is shipped with a default factory Super Master User PIN that can be set (i.e.,
changed) when the lock is in Factory Mode. Once the Super Master User PIN is set, the
Super Master User combination can be used to shelve the lock in the event that the Master
User combination is lost.

Warning:

The setting of the Super Master User PIN is optional, however, if

you do not set the Super Master User PIN before setting the Manager
User PIN, all Super Master User capabilities will be permanently lost.

If you 

do not 

wish to define a Super Master User combination for your lock, proceed

to the following page to complete the lock setup activities. Otherwise, refer to the
Super Master Operations sheet for instruction on setting the Super Master PIN.

The following lock setup activities need to be performed by the Master User to
configure the lock for operations when the lock is in Factory Mode or has been
Shelved.

1.

Set Master User PIN  (p.7)

2.

Set Lock ID for reporting purposes  (p.8)

3.

Toggle sound off  (Optional - p.8)

4.

Change reporting capabilities for lock personnel  (Optional - p.8)

Set Master User PIN

Note:

The default PIN assigned to the Master User is “12345”. The Master User
must change this default PIN before any lock operations can be performed.

Once you have successfully opened the lock using the Master User’s factory
combination, 

the Master User must change the default Master User PIN

 by

completing the following steps:

1.

Press 

#

 

Y

 and then

 1

G

R

Содержание Unicon CL Series

















Отзывы: