background image

12

Toggle Daylight Savings Time

The date and time in the lock can only be programmed from the PC software, but this
operation enables the Master User to “toggle” the Daylight Savings Time (DST) setting at the
lock, moving the clock ahead one hour or back by one hour.

1.

Press 

#

 

Y

, #

 

Y

, #

 

Y

 and then 

1

G

R

2.

Enter the Master User Combination.

The clock in the lock will be set ahead one hour or back one hour depending on
what the previous DST setting was.

2 long green flashes with beeps 

G

G

 = Moved back 1 hour

4 long green flashes with beeps 

G

G

G

G

 = Moved ahead 1

hour

Lock User Operations

The following operations are those that are available for the Lock User.

Set Lock User Access Combination and Secure Lock

1.

Close door and turn the lock knob counterclockwise (CCW) to the “locked” position.

2.

Enter a 4-7 digit combination.

3.

Press 

#

 

Y

.

4.

Enter the 4-7 digit combination again for verification.

5.

Press 

 

Y

.   

G

,  long 

G

,  long 

R

Note:

A “combination locked state” audit record is written at this point followed by a “lock
close” audit record if the knob is in the “locked” position.  If the knob is not fully

turned CCW to the “locked” position, the long red light 

R

 will not display at the end

of the operation and the “lock close” record will not be written.

Unlock with Lock User Access Combination

1.

Enter the 4-7 digit user combination. 

G

 ,  long 

G

2.

Turn the lock knob clockwise (CW) to the “unlocked” position and open the door.

Note:

A “lock open” audit record is written at this point.

Relock with Lock User Access Combination

1.

Close door and turn the lock knob counterclockwise (CCW) to the “locked” position.

2.

Enter the 4-7 digit lock user combination.

3.

Press 

 

Y

.  

G

,  long 

G

,  long 

R

Note:

A “combination locked state” audit record is written at this point followed by a “lock
close” audit record if the knob is in the “locked” position.  If the knob is not fully

turned CCW to the “locked” position, the long red light 

R

 will not display at the end

of the operation and the “lock close” record will not be written.

Содержание Unicon CL Series

















Отзывы: