Kaba Mas DKX Series Скачать руководство пользователя

Страница: 32 / 38

Interface Hardware

Cable Assembly

These steps describe how to attach the rod end connector

(515040 or 515029)

, Figures 23 and 24, and stainless-steel mechanical

cable assembly

(116036)

to the lock and Rim Exit Device chassis. It also describes how to connect the cable assembly and

adjusting the cable length to achieve proper timing of the high security lock bolt retraction relative to the rim exit device latch bolt.

Install Knob Lever Assembly

A. Install the knob lever assembly once the lock assembly and the cover bracket

(515034)

are

successfully installed.

Align the “

Double D

” hole in the knob lever

(515027)

with the “

Double D

” protrusion on the knob assembly

(116035)

and push the lever knob

(515027)

onto the knob assembly

(116035)

C. Align the screw hole in the manual knob

(515043)

with the hole in the knob lever

(515027)

, and hold into slotted

position.

D. Place the knob assembly screw

(515044)

through the hole in the manual knob

(515043)

and tighten into position.

Tighten to a minimum of 15 in.-lbs.

Cover Bracket

(515034)

Figure 22

Screw

(515044)

Knob Assembly

(116035)

Lever, Manual O/R

(515027)

Knob (515043)

Содержание DKX Series







































Результаты поиска

Содержание DKX Series

Отзывы:

Похожие инструкции для DKX Series

Бренды по названию

Популярные бренды

Kaba Mas DKX Series, Руководство по установке

Результаты поиска

Содержание DKX Series

Отзывы:

Похожие инструкции для DKX Series

Бренды по названию

Популярные бренды