2 For Professional Technical Support call 1-844-242-2475
PERFORMANCE
Model No
.
HP
GPM of Water @Total Discharge Pressure of 40 psi
Max.
Pressure
shutoff
Voltage
Pressure
switch
0
ft.
10
ft.
20
ft.
30
ft.
40
ft.
50
ft.
60
ft.
70
ft.
80
ft.
90
ft.
100
ft.
110
ft.
ON OFF
WPD07501K
/WPD07502K
3/4
20
16.3
12.1
6.7
6.3
5.1
4.0
3.0
2.5
1.8
-
-
70PSI
230/115
30
50
WPD10001K
1
24
19.4
13.7
9
8.0
6.5
5.1
4.6
4.4
2.9
2
1.5
70PSI
230/115
30
50
SAFETY INSTRUCTIONS
1.
Pump clear water ONLY with this pump. Do not pump flammable or explosive liquids such as oil, gasoline,
kerosene, ethanol, etc. Do not use in the presence of flammable or explosive vapors. Using this pump with or near
flammable liquids can cause an explosion or fire, resulting in property damage, serious personal injury, and/or
death.
2.
ALWAYS disconnect the power to the pump before servicing.
3.
Do not touch the motor housing during operation. The motor is designed to operate at high temperatures. Do not
disassemble the motor housing.
4.
Do not handle the pump or pump motor with wet hands or when standing on a wet or damp surface, or in water.
5.
Wear safety goggles at all times when working with pumps.
6.
This is a dual voltage 115/230V pump. For model WPD07501K/WPD10001K, VOLTAGE SELECTOR INSIDE
PRESET TO 230V.To change voltage to 115V, please open the terminal cover and set the switch to the proper
voltage. For model WPD07502K, pump will auto select proper voltage. All wiring should be performed by a qualified
electrician.
7.
Protect the electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking the cord. Do not use
damaged or worn cords.
8.
Ensure the electrical power supply is adequate for the requirements of the pump.
9.
Failure to comply with the instruction and designed operation of this unit may void the warranty. ATTEMPTING TO
USE A DAMAGED PUMP can result in property damage, serious personal injury, and/or death.
10.
The pump should be connected to a grounded circuit equipped with a grounded fault interrupter device (GFCI).
11.
Know the pump and its applications, limitations, and potential hazards.
12.
Secure the pump to a solid base.
13.
Periodically inspect the pump and system components. Disconnect the pump from the power supply before
inspecting.
14.
Follow all local electrical and safety codes, along with the National Electrical Code (NEC). In addition, all
Occupational Safety and Health Administration (OSHA) guidelines must be followed.
15.
The motor of this pump has a thermal protector that will trip if the motor becomes too hot. The protector will reset
itself once the motor cools down and an acceptable temperature has been reached. The pump may start
unexpectedly if it is plugged in.
16.
This pump is made of high-strength, corrosion-resistant materials. It will provide trouble-free service for a long time
when properly installed, maintained, and used. However, inadequate electrical power to the pump, dirt, or debris
may cause the pump to fail. Please carefully read the manual and follow the instructions regarding common pump
problems and remedies.
17. Keep fingers and foreign objects away from ventilation and other openings. Do NOT insert any objects into the
motor.
CAUTION:
Do not touch an operating motor. Modern motors are designed to operate at high temperatures. To
avoid burns when servicing the pump, allow it to cool for 20 minutes after shut-down before handling.
Do not allow pump or any system component to freeze. To do so will void warranty.
Periodically inspect the pump and system components.
Wear safety glasses at all times when working on pumps.
Keep the work area clean, uncluttered and properly lighted; store properly all unused tools and equipment.
Keep visitors at a safe distance from the work areas.