K-Rain rps612 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 36

K-Rain rps612 Скачать руководство пользователя страница 15

13

MANUAL OPERATIONS

Run a Single Station

The maximum run time for a station is 12 hours 59 minutes. To manually run a single

station once, turn the dial to the “System Test or Run

Single Station” position.

The display will show:

The default run time for a single station is 10 minutes.

Advance to the selected station by pressing

as many

times as required, and adjust the run time with

and

.

The controller will start running the selected station and the run time will decrement in

the display.

If there is an active pump set for this station, the pump icon will flash once the

button has been pressed, indicating that the pump/master is running. As soon as the

single station run time has elapsed, the unit will revert back to automatic mode. This

means that if you forget to turn the dial back to the “Run” position, the controller will

still run its automatic starts, as scheduled. To turn the station off, change the position

of the main dial, to “OFF”.

HINT:

If you wish to alter the default value from 10 mins to some other value and

set this as the new default time. Turn the dial to “Run Single Station” press the

button. Then alter the run time using the

or

buttons. Once the new

default time is set press the

button again, and the new default will now always

appear when you select a “manual single station”.

Run a System Test

To manually run a system test turn the dial to the “System Test or Run Single Station”
position, press

and

together.

The display will show:

The default run time for a single station is 2 minutes.

If you wish to alter the run time for

this start only

, use

the

and

buttons. Once the correct run time has been entered, turn the

station on and make it run by pressing the

button.

MAC_RPS612_Instruction_Manual.indd 13

20/03/12 4:43 PM

«
...
13
14
15
16
17
...
»

Содержание rps612





































Отзывы:

Нет отзывов