K-Rain rps612 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 36

K-Rain rps612 Скачать руководство пользователя страница 14

12

PROGRAMMING

Continue until all the stations in Program1 have been set with a run time or if a

station(s) is not required to be active in this particular program, ensure that the run

time is set to “OFF”.

NOTE:

To turn a station “OFF” press the

and

at the same time when

the station number is flashing or use

to set minutes to 00 when flashing.

This completes the setting up procedure for automatic program 1.

Select from up to 3 programs using the button for different watering schedules.

On every press of the button the program number will increment. Once on the

desired number, follow the three steps to set an automated program:

1. Set start Times

2. Set Watering Days

3. Set Station Run Times

TIP:

Although the controller will run automatic programs with the main dial in any

position (with the exception of “OFF”), it is advisable to leave the main dial in

the “AUTO RUN” position when not programming or running manual stations or

programs.

Step 3 - Station Run Times (cont.)

Press

or

button to select the station (valve) number, and press the

button and the run time minutes will flash. Alter by using

or

.

Press the

button and the run time hours will flash. Alter by using

or

.

Press the

button and the current station will flash. Select the next station to

change by using

or

and proceed by pressing

and alter using

or

.

MAC_RPS612_Instruction_Manual.indd 12

20/03/12 4:43 PM

«
...
12
13
14
15
16
...
»

Содержание rps612





































Отзывы:

Нет отзывов