JVC RX-D411S - AV Receiver страница 92 Скачать руководство пользователя

Страница: 92 / 117

English

Operating procedure

On the front panel ONLY:

Before you start, remember...

There is a time limit in doing the following steps. If the setting
is canceled before you finish, start from step

again.

Ex.: When setting the DIGITAL IN 1 terminal

Press SETTING.

MULTI JOG now works for the setting operation.

Turn MULTI JOG until the item you want

to set appears on the display.

• As you turn MULTI JOG, the setting items change as

follows:

Press SET.

The current setting of the selected item appears.

Turn MULTI JOG to select the appropriate

setting.

Press SET.

Your setting is stored.

Repeat steps

to set other items if

necessary.

Press SETTING.

The source indication resumes on the display.

1, 7

3, 5

2, 4

SUBWOOFER

FRONT SPK

CENTER SPK

SURROUND SPK

S BACK SPK

S BACK OUT

DIST UNIT

FRONT L DIST

FRONT R DIST

CENTER DIST

SURR L DIST

SURR R DIST

S BACK DIST

S BACK L DIST

S BACK R DIST

EX/ES/PLIIx

DUAL MONO

SUBWOOFER OUT

CROSSOVER

LFE ATT

MIDNIGHT MODE

DIGITAL IN 1

DIGITAL IN 2

DIGITAL IN 3

AUDIO DELAY

HDMI SELECT

CMPNT SELECT

VIDEO OUTPUT

(Back to the beginning)

Setting the speakers

To obtain the best possible surround effect from the Surround
and DSP modes, register the setting about the speaker after all
connections are completed.
• If you have performed Precise Surround Setup on pages 16

to 18, the following settings are not required.

Setting subwoofer information—

SUBWOOFER

Select if you have connected a subwoofer or not.

SUBWFR YES

Select when you have connected a
subwoofer.
The subwoofer indicator (

) lights up on

the display. You can adjust the subwoofer
output level (see page 36).

SUBWFR NO

Select when you have not connected a
subwoofer. Selecting this changes the front
speaker size to “LRG” (see below).

Initial setting:

Setting the speaker size—FRONT SPK (front

speakers), CENTER SPK (center speaker),
SURROUND SPK (surround speakers), S BACK
SPK (surround back speakers)

LRG (large)

Select when the cone speaker size is larger
than 12 cm.

SML (small)

Select when the cone speaker size is smaller
than 12 cm.

Select when you have not connected
the speaker. (Not selectable for the front
speakers.)

Initial setting:

LRG (for the front speakers)
SML (for the other speakers)

NOTES

• If you have selected “SML (small)” for the front speaker size, you

cannot select “LRG (large)” for other speakers.

• When “SUBWOOFER” is set to “NO,” the front speaker size is fixed to

“LRG (large)” (and you cannot select “SML (small)”).

• When “SURROUND SPK” is set to “SML (small),” you cannot select

“LRG (large)” for the surround back speaker.

• When “SURROUND SPK” is set to “NO,” the surround back speaker is

fixed to “NO.”

DVR/DVD

DBS

VCR

29-34_BasicSt.indd 30

06.6.5 5:34:59 PM

Содержание RX-D411S - AV Receiver






















































































































Результаты поиска

Содержание RX-D411S - AV Receiver

Отзывы:

Похожие инструкции для RX-D411S - AV Receiver

Бренды по названию

Популярные бренды

JVC RX-D411S - AV Receiver, Инструкция по эксплуатации

Результаты поиска

Содержание RX-D411S - AV Receiver

Отзывы:

Похожие инструкции для RX-D411S - AV Receiver

Бренды по названию

Популярные бренды