JVC RX-D411S - AV Receiver страница 111 Скачать руководство пользователя

Страница: 111 / 117

English

Operating other
manufacturers’
products

By changing the transmittable signals, you can use the
supplied remote control to operate other manufacturers’
products.

• Refer also to the manuals supplied with the other products.
• To operate those components with the remote control, first

you need to set the manufacturer codes each for the TV,
VCR, CATV converter, DBS tuner, and DVD player.

• After replacing the batteries of the remote control, set the

manufacturer codes again.

• All the functions may not be assigned to the buttons for

some equipment.

To change the transmittable signals for operating a TV

Press and hold TV/SIRIUS

• Keep the button pressed until step

is finished.

Press TV.

Enter the manufacturer code using the

numeric buttons (1 – 9, 0).

See “Manufacturer codes for TV” on the right.

Release TV/SIRIUS

Now, you can perform the following operations on the TV:

TV VOL +/–:

Adjust the volume on the TV.

TV/VIDEO:

Change the input mode (either
video input or TV tuner) on the TV.

After pressing TV, you can perform the following
operations on the TV:

TV/SIRIUS

Turn on or off the TV.

C/–:

Change the channel numbers.

1 – 9, 0, 100+ (

10):

Select the channel numbers.

See the manual supplied with the TV for details.

Try to operate your TV by pressing TV/

SIRIUS

Your TV turns on or off when you have entered the correct
code.

If more than one code is listed for your brand of TV,

try

each one until the correct one is entered.

Manufacturer codes for TV:

Manufacturer

Codes

JVC

Akai

Bell+Howell

Centurion

Coronad

Daewoo

06, 07, 08

Emerson

09, 10, 11, 12, 13

Fisher

GE•Pana

15, 16

GE•RCA

Gold Star

18, 19

Hitachi

20, 21

KTV

22, 23

Magnavox

Marantz

Mitsubishi

Panasonic

26, 27

Philips

Pioneer

Proscan

Quasar

Radioshack

RCA

02, 17, 32, 33, 34, 35

Samsung

36, 37, 45, 46, 47, 48

Sanyo

Sears

Sharp

39, 49, 50

Sony

Symphonic

41, 42

Toshiba

Zenith

43, 44

Initial setting:

Manufacturer codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.

45-54_Others.indd 49

06.6.5 5:30:26 PM

Содержание RX-D411S - AV Receiver






















































































































Результаты поиска

Содержание RX-D411S - AV Receiver

Отзывы:

Похожие инструкции для RX-D411S - AV Receiver

Бренды по названию

Популярные бренды

JVC RX-D411S - AV Receiver, Инструкция по эксплуатации

Результаты поиска

Содержание RX-D411S - AV Receiver

Отзывы:

Похожие инструкции для RX-D411S - AV Receiver

Бренды по названию

Популярные бренды