JVC RX-D411S - AV Receiver страница 75 Скачать руководство пользователя

Страница: 75 / 117

English

Do not connect the AC power cord until all other connections have been made.

Turn off all components before making connections.

• When you connect the components, refer also to their manuals.

Connecting a DBS tuner:

Composite video cable
(not supplied)

S-video cable (not supplied)

DBS tuner

White

Red

: signal flow

Green

Blue

Red

Component video cable (not supplied)

Stereo audio cable (not supplied)

NOTES

• Select the audio and video input setting according to the connection method. See page 21 for

details.

• When connecting a DBS tuner to the COMPONENT VIDEO jacks, select “DBS” for the COMPONENT

select setting (see page 34); otherwise, you cannot view the playback picture on the TV.

• You can enjoy digital sound if using a digital coaxial or optical cable. When shipped from the

factory, the digital optical terminal—DIGITAL IN 2(DBS) on the rear of the receiver is set for a DBS
tuner. For details of digital audio connection, see page 14.

Connecting a TV:

Connect the TV to the appropriate MONITOR OUT jacks to view the playback picture from any other connected video
components.

: signal flow

Composite video cable (not supplied)

S-video cable (not supplied)

Component video cable (not supplied)

Stereo audio cable
(not supplied)

NOTES

• Select the audio input setting according to the connection method. See page 21 for

details.

• You can enjoy digital sound if using a digital coaxial or optical cable. For details of the

digital audio connection, see page 14.

• Select “OTHER” for the video output setting (see page 34).

To left/right audio channel
output

To component video output
• Connect Y, P

, and P

correctly.

To composite video output

To S-video output

To component video input
• Connect Y, P

, and P

correctly.

To left/right audio channel output

To S-video input

To composite video input

White

Red

Green

Blue

Red

06-15_Connection.indd 13

06.6.5 5:26:16 PM

Содержание RX-D411S - AV Receiver






















































































































Результаты поиска

Содержание RX-D411S - AV Receiver

Отзывы:

Похожие инструкции для RX-D411S - AV Receiver

Бренды по названию

Популярные бренды

JVC RX-D411S - AV Receiver, Инструкция по эксплуатации

Результаты поиска

Содержание RX-D411S - AV Receiver

Отзывы:

Похожие инструкции для RX-D411S - AV Receiver

Бренды по названию

Популярные бренды