JVC RX-5060B Скачать руководство пользователя страница 60

Страница: 60 / 116

English

Speaker distance

—FRONT L DIST, FRONT R DIST,

CENTER DIST, SURR L DIST, SURR R DIST

Set the distance from the listening point within the range of
0.3 m (1 ft) to 9.0 m (30 ft), in 0.3 m (1 ft) intervals.

• When shipped from the factory, distance for each speaker is

set to “3.0m (10FT).”

Note:

You cannot set the speaker distance for the speakers you have
selected “NONE.”

Ex. In the above case, set the speaker distance as follows:

Front speakers:

3.0m (10FT)

Center speaker:

3.0m (10FT)

Surround speakers:

2.7m (9FT)

Setting the Bass Sounds

You can adjust subwoofer and bass sounds precisely according to
your preference.

Subwoofer output

—SUBWOOFER OUT

The subwoofer emits the LFE signals* and the bass elements of
each speaker set to “SMALL.”
You can make the bass elements of the front speaker channels
(MAIN) emitted through the subwoofer.

Select one of the following:

SWFR LFE:

Select to emit the LFE signals and the bass
elements of each speaker set to “SMALL.”

SWFR LFE+MAIN:

Select to emit the bass elements of the

front speakers’ channels (MAIN) adding to the
effect of “SWFR LFE” when no bass elements
are emitted through the subwoofer.

Notes:

• When “SUBWOOFER” is set to “SUBWOOFER NO” (see the left

column), this function is not available.

* The LFE signals are emitted only when playing the following

software with the LFE signals:
– Dolby Digital multi channel software
– DTS multi channel software
When playing an analogue source or a linear PCM software, no
LFE signals are emitted.

Setting the Speakers

To obtain the best possible surround effect from the Surround and
DSP modes, register the setting about the speaker arrangement after
all connections are completed.
• If you have used Quick Speaker Setup on page 16, this setting is

not required.

Subwoofer setting

—SUBWOOFER

Select whether you have connected a subwoofer or not.

SUBWOOFER YES:

Select when a subwoofer is connected.

SUBWOOFER NO:

Select when no subwoofer is used.

Note:

If you have selected “SUBWOOFER NO” for the subwoofer, you
cannot use the SUBWOOFER OUT ON/OFF button on the front
panel.

Speaker size

—FRNT SPEAKERS, CNTR SPEAKER,

SURR SPEAKERS

Select the size for each connected speaker.

LARGE:

Select when the speaker size is relatively large.

SMALL:

Select when the speaker size is relatively small.

NONE:

Select this when you have not connected a
speaker. (Not selectable for the front speakers.)

Notes:

• Keep the following comments in mind as reference when

adjusting.
– If the size of the cone speaker unit built in your speaker is

larger than 12 cm, select “LARGE,” and if it is smaller than 12
cm, select “SMALL.”

• If you have selected “SUBWOOFER NO” for the subwoofer

setting, you can only select “LARGE” for the front speakers.

• If you have selected “SMALL” for the front speakers, you cannot

select “LARGE” for the center and surround speakers.

Setting the Speaker Distance

The distance from your listening point to the speakers is another
important element to obtain the best possible sound of the Surround
and DSP modes. Set the distance from your listening point to the
speakers.
By referring to the speaker distance setting, this unit automatically
sets the delay time of the sound through each speaker so that sounds
through all the speakers can reach you with the same timing.
• If you have used Quick Speaker Setup on page 16, this setting is

not required.

Measuring unit

—DISTANCE UNIT

Select which measuring unit you use.

UNIT METER:

Select to set the distance in meters.

UNIT FEET:

Select to set the distance in feet.

Basic Settings

2.1 m

(7 ft)

2.4 m