JVC MX-J170V Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 78

background image

MX-J170V

1-26

Turn off the power switch and,disconnect the
power cord from the ac outlet.

Replace the pickup with a normal one.(Refer
to "Pickup Removal" on the previous page)

Plug the power cord in,and turn the power on.
At this time,check that the laser emits for
about 3seconds and the objective lens moves
up and down.
Note: Do not observe the laser beam directly.

Play a disc.

Check the eye-pattern at TP1.

Finish.

Maintenance of laser pickup

(1) Cleaning the pick up lens
Before you replace the pick up, please try to
clean the lens with a alcohol soaked cotton
swab.

(2) Life of the laser diode
When the life of the laser diode has expired,
the following symptoms will appear.

1. The level of RF output (EFM output:ampli
tude of eye pattern) will below.

Is the level of

RFOUT under

1.8V 0.2Vp-p?

Replace it.

NO

YES

O.K

(3) Semi-fixed resistor on the APC PC board
The semi-fixed resistor on the APC printed circuit board which is attached to the pickup is used to adjust the
laser power.Since this adjustment should be performed to match the characteristics of the whole optical block,
do not touch the semi-fixed resistor.
If the laser power is lower than the specified value,the laser diode is almost worn out, and the laser pickup should
be replaced.
If the semi-fixed resistor is adjusted while the pickup is functioning normally,the laser pickup may be damaged
due to excessive current.

Replacement of laser pickup

«
...
24
25
26
27
28
...
»

Содержание MX-J170V















































































Отзывы:

Нет отзывов

Похожие инструкции для MX-J170V

Бренд: Tannoy Страницы: 10

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 16

Бренд: DAS Страницы: 6

Бренд: dB Technologies Страницы: 4

Бренд: dB Technologies Страницы: 89

Бренд: dbx Страницы: 51

Бренд: dBTechnologies Страницы: 4

Бренд: ICMA Страницы: 2

Бренд: Pan Acoustics Страницы: 18

Бренд: Sanlien Страницы: 42

Бренд: Onkyo Страницы: 10

Бренд: Bem Страницы: 28

Бренд: VENCO Страницы: 31

Бренд: Jam Страницы: 3

Бренд: TAD Страницы: 2

Бренд: Thodio Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды