JVC MX-J170V Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 78

background image

MX-J170V

1-4

Preventing static electricity

1. Grounding to prevent damage by static electricity

Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged,
can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.

2. About the earth processing for the destruction prevention by static electricity

In the equipment which uses optical pick-up (laser diode), optical pick-up is destroyed by the static electricity of
the work environment.
Be careful to use proper grounding in the area where repairs are being performed.

2-1 Ground the workbench

Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over
it before placing the traverse unit (optical pickup) on it.

2-2 Ground yourself

Use an anti-static wrist strap to release any static electricity built up in your body.

3. Handling the optical pickup

1. In order to maintain quality during transport and before installation, both sides of the laser diode on the
replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)

2. Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power
source can easily destroy the laser diode.

4. Handling the traverse unit (optical pickup)

1. Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.

2. Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific
details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse
unit. Be careful not to take too long a time when attaching it to the connector.

3. Handle the flexible cable carefully as it may break when subjected to strong force.

4. It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it

Conductive material
(conductive sheet) or iron plate

(caption)
Anti-static wrist strap

Attention when CD mechanism assembly is decomposed

1. Remove the CD changer unit.
2. Remove the CD changer mechanism.
3. Solder is put up before the card wire is removed from the pickup unit
connector on the CD mechanism assembly.
(When the card wire is removed without putting up solder, the CD pick-up
assembly might destroy.)
4. Please remove solder after connecting the card wire with the pickup unit
connector when you install picking up in the substrate.

*Please refer to "Disassembly method" in the text for pick-up and how to
detach the CD mechanism assembly.

Soldering

Fig.1

Fig.2

Card wire

Card wire

Pickup unit
connector

Pickup unit
connector

CD changer unit

CD mechanism

«
...
2
3
4
5
6
...
»

Содержание MX-J170V















































































Отзывы:

Нет отзывов

Похожие инструкции для MX-J170V

Бренд: Tannoy Страницы: 10

Бренд: FAAC Страницы: 60

Бренд: KEF Страницы: 4

Бренд: 3SIXT Страницы: 4

Бренд: DAPAudio Страницы: 12

Бренд: JBL Страницы: 2

Бренд: Olympia Страницы: 62

Бренд: Q Acoustics Страницы: 8

Бренд: Q Acoustics Страницы: 19

Бренд: S&P Страницы: 72

ACUSTICA H series

Бренд: RCF Страницы: 10

Smart Home Monitoring

Бренд: Rogers Страницы: 5

Бренд: DUB Edition Страницы: 9

Бренд: Magicsing Страницы: 23

TIG200PACDC PFC

Бренд: Jasic Страницы: 52

Бренд: Steren Страницы: 12

Бренд: Caliber Страницы: 12

Бренд: Jam Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды