1-3
Fig. 1-2-2d
A
CN1601
The excessive length portion
of wire should be reat as figure.
DRUM
A/C HEAD
CN916
CN2001
Make a crease
CN511
Make a crease
FRONT PANEL
CN7001
B
Make a crease
P/S CONV PWB
Make a crease
DETAIL "A"
About 5cm
CN7001
Push the FFC wire from the FRONT PANEL
to rear side.
CN7002
CN7005
DETAIL "B"
CN5001
(WR2b)
<Note 2a>
To Front S Jack board assembly
To Adv. Jog board assembly
(WR2a)
<Note 2a>
(WR2c)
(WR2a)
d
a
Q3
00
3
b
Q3
00
2
JS
30
01
c'
D3
00
1
b
CN
50
01
d'
b
c'
"Z"
h
f
k
e
a
f
c
c
b
f
f
c'
c'
d'
h
b
b
e
<Note 2b>
<Note 2b>
[2] Front panel
assembly
PC Support
[2]Mini front board
assembly
[5]Main board
assembly
Knob assembly
Cassette door
(L2a)
(L2d)
(L2c)
(L2a)
(L2b)
(L2b)
a
d
<Note 3c>
d
g
e
Inertia plate
Roller arm assembly
<Note 3e>
[3] Mechanism assembly
Drum assembly
<Note 3c>
<Note 3c>
<Note 3b>
<Note 3a>
<Note 3a>
<Note 2a>
(WR3a)
(S3c)
(S3e)
(S3d)
(S2a)
(S3a)
(S2a)
(S3b)
(L3b)
(P3a)
(S3g)
(W3a)
(L3c)
g
NOTE) After attached ROLLER ARM ASS'Y,
tighten screw(S3g) with slit washer(W3a).
NOTE) When attaching ROLLER ARM ASS'Y,
attach the hook(L3c) before the spring(P3a).
NOTE) INERTIA PLATE should be attached so as to ser small
diameter of central round hole above.
(S4a)
(S4a)
[4] S/P conveter board
assembly
(L4a)
h
k
h
<Note 2a>
<Note 2a>
<Note 2a>
(WR3b)
right side
right side
back side
back side
JS3001
Accord the position of V gap on R. Encoder and PWB silk " ".
<Phase alignment>
Accord the position of Boss on R. Encoder and PWB silk " ".
For the prevention of the DRUM FPC damage.
When you attach the Mechanism assembly on Bottom chassis.
Attach the Mechanism assembly after the positioning boss "z" of the
Bottom chassis is matched to the positioning hole of the Mehcanism assembly.
(S5a)
(S5b)
(S5b)
(S5b)
Insert the bushing of POWER CORD
so as not to twist the cord.
(WR4a)
(WR3a)
NOTE)INSERT FFC WIRE TO THE CONNECTOR
BEFORE ATTACHING JOG/SW PWB TO F.PANEL.
NOTE) INSERT FFC WIRE TO THE CONNECTOR BEFORE
CN7003
ATTACHING JOG/SW PWB TO F.PANEL.
CN7108
Front panel assembly back side
Front S Jack board assembly
(S2b)
(WR2a)
<Note 2a>
(WR2b)
<Note 2a>
(S2c)
Back side
ADV. Jog board
assembly
Switch lever
<Note 2b>
NOTE) WHEN YOU FIX FRONT S Jack PWB WITH THE SCREW.
PUT JIG UNDER FRONT PANEL ASS'Y.
Right side
Back side
OK
NG
CN
electrode side
supporting side
Except U/U(C)/JPN
NOTE
CN
CN
1. Insert direction of FFC WIRE as follows.
2. FFC WIRE and DRUM FPC WIRE should
be insert as follows.
3. Insert direction of POWER CORD.
NEUTRAL
WHITE LINE
CN5001
BLUE
NEUTRAL
CN5001
U/U(C)/JPN
90
°
[1] Top cover
(S1a)
(S1a)
REAR SIDE
(S1b)
f
f
f
f
[6] Bottom cover
(L6b)
(L6a)
(L6a)
(L6a)
(L6b)
(L6c)
ONLY USED
FOR HR-S7955MS
ONLY USED FOR
HR-S6955MS,
HR-S7955MS
ONLY USED
FOR HR-S7955MS
(L5a)
Switch knob
<Note 2b>
www.freeservicemanuals.info
3/28/2017
Digitized in Heiloo Netherland
