EN
37
ENTER CHANNEL POSITION
6
Press
PR +/–
.
SET TAPE SPEED
7
Press
SP/LP/EP (
)
to set the tape speed.
●
It is not possible to select EP mode if "COLOUR
SYSTEM" is set to "MESECAM". (
pg. 17)
(VHS deck only)
SET VPS/PDC MODE
8
Press
VPS/PDC
to select "ON" or "OFF".
If "VPS/PDC ON" is displayed on the screen or "VPS/
PDC" is lit on the display panel, VPS/PDC is set to ON.
If "VPS/PDC OFF" is displayed on the screen or "VPS/PDC"
is not lit on the display panel, VPS/PDC is set to OFF.
"VPS/PDC Recording" in the right column.
RETURN TO NORMAL
SCREEN
9
After confirming all information is correct, press
PROG
or
OK
. "PROGRAM COMPLETED" appears on the
screen for about 5 seconds, then normal screen
appears. If "PROGRAM OVERLAPPED" appears on the
TV screen and "Err" on the front display panel, see page
39.
●
Repeat steps
1
–
9
for each additional programme.
ENGAGE RECORDER’S
TIMER MODE
10
Press
‰
(
TIMER
). The recorder turns off automatically
and
‰
appears on the display panel.
●
To disengage the timer, press
‰
(
TIMER
) again.
To Timer-Record Weekly Or Daily Serials . . .
. . . anytime during steps
2
through
9
, press
WEEKLY
(
NUMBER
key "9") for weekly serials or
DAILY
(
NUMBER
key "8") for daily
serials (Monday – Friday). Either "WEEKLY" or "DAILY" appears
on the screen. Pressing the button again makes the correspond-
ing indication disappear.
SP
Satellite Receiver Users
To timer-record a satellite broadcast using Express Timer
Programming:
1
Perform "Satellite Receiver Control Setting" (
pg. 13).
2
Perform steps
1
–
10
. In step
6
, press the
NUMBER
key
"0" to change "TV PROG" to "SAT". The display panel
shows "L2" for the preset position. Then press
PR +/–
to
enter the preset position for the satellite broadcast. In
step
8,
you cannot set "VPS/PDC" to "ON".
3
Leave the satellite receiver's power on.
NOTE:
You can programme the VHS deck and the DV deck to timer-
record as many as 6 programmes each. If you try to programme
each deck to record a seventh, "PROGRAM FULL" appears on
screen and "FULL" appears on the front display panel. To record
the extra programme, you must first cancel any unnecessary
programmes (
pg. 38).
VPS/PDC Recording
Now available from some TV stations, PDC (Programme
Delivery Control) and VPS (Video Programme System) are
service designed to assure safe, accurate timer recording.
With this system, special code signals are transmitted
together with the audio/video signals. These code signals
control your video recorder and have precedence over the
advertised times you may have preset into the timer. This
means that your recorder will start and stop recording when
the preset TV programmes actually start and end — even if
the broadcast time of a preset TV programme is changed.
NOTES:
●
When you use Express Timer Programming, set the start
time (VPS or PDC time) exactly as advertised in the TV
listing. A different time than advertised will result in no
recording.
●
VPS/PDC recording is also possible when a satellite
receiver or a cable system is connected to AV2 (L-2) IN/
DECODER on your recorder.
●
VPS/PDC recording is also possible via the AV1 (L-1) IN/
OUT connector.
How to check if the station being received transmits
a VPS/PDC signal (VHS deck only)
1
Press
– –:– –
until the channel position appears on the
display panel.
2
Hold down
START+
for about 5 seconds.
●
"VPS/PDC" appears blinking on the display panel.
If a VPS/PDC signal is detected from the station, "VPS/
PDC" will stop blinking.
If no VPS/PDC signal is detected from the station, "VPS/
PDC" will blink at a slower rate.
3
Press
– –:– –
or
START+
again to return to normal display.
VHS – P1 –
START
STOP
21:00
=
22:00
SP
VPS/PDC OFF
DATE
TV PROG
25.12
1
ARD
[+/–]
=
[0] : SAT
[PROG] : EXIT
Timer Warning
If you have programmed your
recorder to timer-record a
programme or a series of
programmes, a warning
appears on screen to tell you
that the recording is to start in
5 minutes.
NOTES:
●
The warning only appears if
you’re not in the Timer mode at that time.
●
If this recorder is being used as the player for tape
dubbing, the warning screen is recorded on the tape in
the other video recorder.
The warning blinks for the entire 5 minutes leading up to
the start of timer recording. To clear the display, press .
– WARNING–
TIMER RECORDING
TO START SOON
[
]
Содержание HR-DVS2EU
Страница 87: ...MEMO ...
