JVC DPT 115 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 37

background image

KY-F55 Configuration

Attach the 8-pin circular DIN male connector of the lens control cable (ACL99088000) to the 8-
pin female DIN on the trunnion of the pan and tilt. Attach the other end, a male Hirose connector
to the female Hirose on the teleconferencing lens.

At this time there will be one cable on the teleconferencing lens not connected. Plug this male
Hirose connector into the female “LENS” connector on the rear of the KY-F32 camera.

DPT 115 LDCC Cable Installation (Used with LDCC Option Only)

Attach the 9-pin Dsub male connector of the DPT 115 LDCC cable (ACA96052200) to the
“RS232” connector on the base of the pan and tilt. Connect other end, 6-pin male mini-DIN to
“REMOTE” connector on rear of camera.

2/12/05

Document D0153

30

«
...
28
29
30
31
32
...
»

Содержание DPT 115






































Отзывы:

Нет отзывов

Похожие инструкции для DPT 115

Бренд: Park Play Страницы: 18

Бренд: Zell Страницы: 33

Бренд: Oki Страницы: 8

Stylus Pro 7900

Бренд: X-Rite Страницы: 36

Бренд: Panasonic Страницы: 2

SuperStack 3 4300

Бренд: 3Com Страницы: 8

Бренд: 3B Medical Страницы: 7

Бренд: 360Rize Страницы: 17

Бренд: 360fly Страницы: 3

Бренд: 4B Страницы: 16

Бренд: Safemate Страницы: 12

MIW-DUAL-SIGNAL-BAY

Бренд: Panamax Страницы: 2

SmartDiag2GO GD201-O

Бренд: OCTO Страницы: 5

Бренд: Cequent Страницы: 9

Бренд: Digitus Страницы: 9

Бренд: REV Страницы: 2

2 SD Card Memory Module NI 9802

Бренд: National Instruments Страницы: 16

Бренд: Cateye Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды