JVC DPT 115 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 37

background image

6.9.5 RS-232 Cable Installation.

The RS-232 cable provides the control interface between the DPT 115 pan and tilt head and the
controller if an RS-232 interface is desired. Figure 3-3 illustrates a typical RS-232 cable.

P2

P1

5

3

2

5

3

2

Red

White

Black

Black

Red

White

Black

Black

Figure 3-3: Typical RS-232 Cable

Connect the plug (male) end of RS-232 to the nine pin “D” connector on the pan and tilt head.
Connect the other end of the cable to the connector on the RS-232 controller.

6.9.6 Power Cable Installation

Attach the power cord plug on the power supply provided with the pan and tilt head to the DC
jack on the connector panel labeled “POWER”.

6.9.7 Lens I/F Connector

This connector is not used for most applications. No connections should be made to this
connector during normal setup. In the event this connector is to be used a full description will be
provided in the application note for that particular configuration.

Lens Control Cable Installation

6.9.8.1 KY-F32 Configuration

Attach the 8-pin circular DIN male connector of the lens control cable (ACL99088000) to the 8-
pin female DIN on the trunnion of the pan and tilt. Attach the other end, a male Hirose connector
to the female Hirose on the teleconferencing lens.

At this time there will be one cable on the teleconferencing lens not connected. Plug this male
Hirose connector into the female “LENS” connector on the rear of the KY-F32 camera.

2/12/05

Document D0153

29

«
...
27
28
29
30
31
...
»

Содержание DPT 115






































Отзывы:

Нет отзывов

Похожие инструкции для DPT 115

AWPH360N - PAN/TILT HEAD

Бренд: Panasonic Страницы: 48

Бренд: Xenith Страницы: 17

Бренд: Zamel Страницы: 12

Бренд: Kabuto Страницы: 40

Бренд: Celestron Страницы: 24

Бренд: Kasanova Страницы: 22

Бренд: Godox Страницы: 31

Бренд: Swisher Страницы: 1

Бренд: Hama Страницы: 75

Бренд: minnid Страницы: 44

Бренд: PCB Piezotronics Страницы: 12

Powereco 10 000

Бренд: X-Moove Страницы: 3

Бренд: INNOBIZ Страницы: 88

Бренд: QualGear Страницы: 6

Бренд: AC Schnitzer Страницы: 16

MCL-7000 Series

Бренд: Dakota Digital Страницы: 2

Бренд: Hach Страницы: 52

Бренд: Element14 Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды