background image

5.1.2 Communications Interface 

Control of the pan and tilt is accomplished by sending packets of ASCII characters to the head. 
The standard communications protocol is 9600 baud, eight data bits, one stop bit , and no parity. 
These commands tell the head and lens which direction and at what rate to move. Preset related 
commands are also passed over the communication link between the head and the controller. In 
most cases the communications link is either RS-422 or RS-232. The micro-processor in the pan 
and tilt head will automatically detect the communication type being received, and select that 
communication interface type to transmit data back to the controller. The pan and tilt also has the 
provision to use both type interfaces concurrently for special purpose application 

 

The RS-422 communications interface is also used to pass camera control commands to the 
camera in the camera control mode (LDCC) for JVC cameras. In this mode the controller sends 
the camera commands to the head in RS-422 format on the four wire cable. The commands are 
received in RS-422 and converted to TTL levels by electronics in the head. These commands are 
the sent out the RS-232 connector via the pan and tilt LDCC cable (P/N ACA96037900) to the 
camera. These camera control commands enter the camera on the six pin mini-DIN “REMOTE” 
connector on the rear panel of the camera  

 

5.1.3 RS-422 Connector 

The connector labeled “RS422” on the connector plate is a six position, four conductor modular 
jack. This connector provides differential 0 to +5 VDC  voltage signals to and from the digital 
pan and tilt head, this is the most common interface from the controller to the heads. Shown 
below is the pin-out for the RS-422 connector. The pin assignment for this connector follows: 

 

Pin 2

Pin 5

Pin 6

Not

Used

Pin 1

Not

Used

 

 

 

 

The pin assignment for this connector follows: 

Pin #   

Description 

 

P/T Data Out - 

 

P/T Data Out + 

 

P/T Data In - 

 

P/T Data In + 

2/12/05  

Document D0153

 

14

Содержание DPT 115






































Отзывы: