JVC DPT 115 Скачать руководство пользователя страница 37

Страница: 37 / 37

2/12/05

Document D0153

10. GLOSSARY

Base: Bottom portion of the pan & tilt head which does not move.

BNC: A connector type used to interface video sources

CCTV Lens: A lens in which the zoom and focus motors are driven directly from the
DPT 115 lens control electronics.

Controller: The ESI Model 180 Pan & Tilt and Camera/Lens Controller.

DIN: Large circular connector on the trunnion of the pan & tilt head. Mates to the large
circular DIN connector on the ESI furnished W2 connector.

LED: Light Emitting Diode.

Limit Switch: Switches which disengage the electronic drive when the pan & tilt head
reaches a preset position.

MINI DIN: A small circular connector commonly used on cameras. Miniature version of
the DIN connector.

Position Keys: Locators on the Vertical face of the pan & tilt head which allows the “L”
bracket to be located in either of two positions.

Teleconferencing Lens: A lens in which the zoom and focus control electronics are
located within the lens. The DPT 115 supplies a single wire interface to each of the zoom
and focus electronic inputs.

Trunnion: Moveable top portion of the pan & tilt head.

Содержание DPT 115






































Результаты поиска

Содержание DPT 115

Отзывы:

Похожие инструкции для DPT 115

Бренды по названию

Популярные бренды

JVC DPT 115, Руководство по эксплуатации

Результаты поиска

Содержание DPT 115

Отзывы:

Похожие инструкции для DPT 115

Бренды по названию

Популярные бренды