background image

CH-X400/CH-X450

1-9

Can be removed at the stud position
(at the widest hole)

Remove

Shift

Third gear

Fig. 15

Fig. 16

Fig. 17

Fig. 18

Remove the E-washer

Third gear

Slide and remove the rod inside

Slide

Rod

Top Plate

Remove

After lifting

3

3

3

3

3

e

Rear slider

1. Position the unit with the front section facing down.  Rotate 

the third gear located on the back of the main unit in the 
direction of the arrow (clockwise).

2. Shift the rear slider in the direction of the arrow and remove it 

at the rear slider mounting position (at the widest hole).

Front slider

1. Position the unit with the rear section facing down.  Rotate the 

third gear located on the bottom of the unit in the direction of 
the arrow (clockwise) until the front slider is shifted to the 
outermost position.

2. Remove the E-washer securing the front slider to remove the 

front slider from the chassis.

Top plate

1. Remove the nine screws (3) securing the top plate.
2. Disconnect the section (e) attached to the rear of the unit, 

then lift the top plate slightly.

3. Slide the top plate toward the rear of the unit to remove the 

upper rod from the top plate.

www. xiaoyu163. com

QQ 376315150

9

9

2

8

9

4

2

9

8

TEL 13942296513

9

9

2

8

9

4

2

9

8

0

5

1

5

1

3

6

7

3

Q

Q

TEL  13942296513  QQ  376315150  892498299 

TEL  13942296513  QQ  376315150  892498299 

http://www.xiaoyu163.com

http://www.xiaoyu163.com

Содержание CH-X400




























































Отзывы: