Juniper MX2008 Скачать руководство пользователя страница 66

Страница: 66 / 69

WARNING:

The attached power cable is only for this product. Do not use

the cable for another product.

Compliance Statements for NEBS

•

The equipment is suitable for installation as part of the Common Bonding Network
(CBN).

•

The equipment is suitable for installation in locations where the National Electrical
Code (NEC) applies.

•

The battery return connection is to be treated as an isolated DC return (i.e. DC-I), as
defined in GR-1089-CORE.

•

For Juniper Networks systems with AC power supplies, an external surge protective
device (SPD) must be used at the AC power source.

Compliance Statements for EMC Requirements for Juniper Networks Devices

•

Canada on page 66

•

European Community on page 66

•

Israel on page 67

•

Japan on page 67

•

United States on page 67

Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

European Community

This is a Class A product. In a domestic environment, this product might cause radio
interference in which case the user might be required to take adequate measures.

MX2008 3D Universal Edge Router Quick Start

Содержание MX2008



































































Результаты поиска

Содержание MX2008

Отзывы:

Похожие инструкции для MX2008

Бренды по названию

Популярные бренды

Juniper MX2008, Быстрый старт

Результаты поиска

Содержание MX2008

Отзывы:

Похожие инструкции для MX2008

Бренды по названию

Популярные бренды