Juniper MX2008 Скачать руководство пользователя страница 52

Страница: 52 / 69

13.

Reinstall the metal PDM wiring cover, and using a number 2 Phillips (+) screwdriver,
tighten the four captive screws on the metal AC wiring compartment.

14.

Use the provided plastic cable tie to fasten the AC power cord to the PDM.

15.

Verify that the AC power cord does not touch or block access to router components,
and that it does not drape where people could trip on it.

16.

Repeat the procedure for the other three-phase wye AC PDMs.

17.

Connect the three-phase wye AC power cord mating connector to the AC power cord
connector (see

Figure 37 on page 52

Table 7 on page 52

shows the approved

three-phase wye AC power cord mating connector specifications.

Figure 37: Three-Phase Wye AC Power Cord Mating Connector

g000038

Table 7: Three-Phase Wye AC Power Cord Mating Cable Connector
Specifications

Description

Manufacturer Part Number

Cable

32-amp, 400 volt IP44 3 pole,
5 wire with brass contacts (red)

PCE 225-6

Three-phase wye

NOTE:

The three-phase wye AC power cord mating connector is not

supplied by Juniper Networks.

WARNING:

Do not touch the power connectors on the PDM. They can contain

dangerous voltages.

MX2008 3D Universal Edge Router Quick Start

Содержание MX2008



































































Результаты поиска

Содержание MX2008

Отзывы:

Похожие инструкции для MX2008

Бренды по названию

Популярные бренды

Juniper MX2008, Быстрый старт

Результаты поиска

Содержание MX2008

Отзывы:

Похожие инструкции для MX2008

Бренды по названию

Популярные бренды