JUMO dTRANS CR 02 Скачать руководство пользователя страница 49

Страница: 49 / 120

8 Calibrating a conductivity sensor

8.3

Calibration of the temperature coefficient of the sample
medium

✱

Make preparations, see chapter 8.2 "General information", page 47.

✱

Start calibration, see chapter 8.2.3 "Ways to start the calibration", page 48.

✱

Select "TEMP.COEFF. LIN.".

The current sensor temperature appears in the display (+ flashing) (1).

✱

Enter the required working temperature and confirm your entry with the

key.

Now the source of temperature acquisition can be selected (manually, or using
the temperature input of the PSU board, or the temperature input via the
optional board). This source will be active for the duration of the calibration.

An example follows: automatic temperature acquisition using the temperature
sensor integrated into the conductivity sensor.

(1)

PGM

The working temperature must be at least 5 °C above or below the reference
temperature (25.0 °C).

Содержание dTRANS CR 02

























































































































Результаты поиска

Содержание dTRANS CR 02

Отзывы:

Бренды по названию

Популярные бренды

JUMO dTRANS CR 02, Руководство по эксплуатации

Результаты поиска

Содержание dTRANS CR 02

Отзывы:

Бренды по названию

Популярные бренды