JUMO dTRANS CR 02 Скачать руководство пользователя страница 37

Страница: 37 / 120

6 Operation

Activate Manual mode

The instrument is in Display mode

✱

Press the

and

keys for less than 2 seconds.

The word MANUAL appears in the status line of the display.

Control is not longer via the instrument. The output level of the controllers
is 0%.

Controller 1 is activated by the

key. In this case the output level of

controller 1 is 100%.

Controller 2 is activated by the

key. In this case the output level of

controller 2 is 100%.

Deactivation

✱

Press the

key.

Control is once again through the outputs of the instrument.
The word MANUAL appears in the status line of the display.

6.8.2

Simulation of binary outputs

Activate simulation

✱

Set ADMINISTR. LEVEL/PARAMETER LEVEL/BINARY OUTPUTS/BINARY
OUTPUT1 ( ... 8) "Manual mode no simulation, Inactive or Active".

No simulation

= No Manual mode, control is via device.

Inactive

= Relay K1 or K2 is de-energized;the word MANUAL

appears in the status line of the display

Active

= Relay K1 or K2 is energized;the word MANUAL appears

in the status line of the display

EXIT

If the

keys (alone) are pressed for longer than 3 seconds, the instrument

switches to language selection.

If the

and

keys are pressed for longer than 3 seconds, the instrument

goes into HOLD mode.

Then the outputs of the instrument respond according to the default settings.

To exit HOLD mode, press the

and

keys for longer than 3 seconds.

EXIT

In the factory setting of the instrument the MANUAL mode parameter is set to
"No simulation" and can only be activated by the administrator!
This parameter must first be released for other users, see "Release level",
page 32.

If a higher order switching function has been assigned to an output, Simulation
mode is not possible for that output.

Содержание dTRANS CR 02

























































































































Результаты поиска

Содержание dTRANS CR 02

Отзывы:

Бренды по названию

Популярные бренды

JUMO dTRANS CR 02, Руководство по эксплуатации

Результаты поиска

Содержание dTRANS CR 02

Отзывы:

Бренды по названию

Популярные бренды