JUMO dTRANS CR 02 Скачать руководство пользователя страница 28

Страница: 28 / 120

6 Operation

Minimum and maximum values of the main value "1:" (mS/cm, µS/cm,
MOhm x cm, mV, %, ppm) and the temperature "T:" are displayed.

The extreme values of the main measurement variable and the temperature are
not mutually assigned (e.g. not 813 µS/cm at 24.3 °C).

6.5.3

Min/max values of the optional inputs

Activating the display

The instrument is in Measuring mode (normal display)

✱

Briefly press the

key (several times if necessary).

Minimum and maximum values of the optional inputs (1, 2 and 3) are
displayed

6.5.4

Output level

Activating the display

The instrument is in Measuring mode (normal display)

✱

Briefly press the

key (several times if necessary).

The current output levels of the controller outputs.

6.5.5

Current values of the main entries

Activating the display

The instrument is in Measuring mode (normal display)

✱

Briefly press the or

key (several times if necessary).

The current values of the main output are displayed.

Содержание dTRANS CR 02

























































































































Результаты поиска

Содержание dTRANS CR 02

Отзывы:

Бренды по названию

Популярные бренды

JUMO dTRANS CR 02, Руководство по эксплуатации

Результаты поиска

Содержание dTRANS CR 02

Отзывы:

Бренды по названию

Популярные бренды