JUMO ATH-SE-2 Скачать руководство пользователя страница 5

Страница: 5 / 30

1 Safety information

Safety information

1.1

Warning symbols

WARNING!

This symbol in connection with the signal word indicates that

personal injury

may occur if the respective

precautionary measures are not carried out.

CAUTION!

This symbol in connection with the signal word indicates that

material damage or data loss

will occur

if the respective precautionary measures are not taken.

1.2

Note symbols

NOTE!

This symbol refers to

important information

about the product, its handling, or additional benefits.

READ THE DOCUMENTATION!

This symbol, which is attached to the device, indicates that the associated

documentation for the de-

vice

must be

observed

. This is necessary to identify the nature of the potential hazard, and to take

measures to prevent it.

DISPOSAL!

At the end of its service life, the device and any batteries present do not belong in the trash! Please en-
sure that they are

disposed of

properly and in an

environmentally friendly

manner.

Содержание ATH-SE-2































Результаты поиска

Содержание ATH-SE-2

Отзывы:

Бренды по названию

Популярные бренды

JUMO ATH-SE-2, Руководство по эксплуатации

Результаты поиска

Содержание ATH-SE-2

Отзывы:

Бренды по названию

Популярные бренды