JUMO 202710/30 Скачать руководство пользователя страница 38

Страница: 38 / 44

9 Error and system messages

Error messages during measurement

Error message during automatic alignment

Display

Cause

Remedy

Battery voltage low,
the function can still be guaranteed
only for a short time.

Insert new battery

Battery is used up

Insert new battery

During mains operation: incorrect voltage Test power supply unit, replace if necessary

No display
or muddled char-
acters, device
does not respond
to keys being
pressed

Battery voltage too low

Insert new battery

During mains operation: power supply
unit defective or incorrect voltage/polarity

Test power supply unit, replace if necessary

System error

Remove battery or power supply unit, wait briefly
before reconnecting

Device error/device defect

Send in device for repair

Measuring range exceeded

Check whether the measured value is above the
permissible measuring range of the sensor

Measuring cell is defective

Send in device for repair

Measuring range not reached

Check whether the measured value is below the
permissible measuring range of the sensor

Measuring cell is defective

Send in device for repair

System error

Send in device for repair

Measuring range exceeded or not
reached by a significant margin

Check whether the measured value is within the
permissible measuring range of the sensor

Display value cannot be calculated,
measuring range or input value
exceeded

Check measuring range

Display value cannot be calculated,
measured values too unstable

Wait for signal control of the device

Preset calibration interval elapsed

Calibrate device

Last calibration invalid

Display

Cause

Remedy

Relative cell constant too large

Determined relative cell constant
must not be > 1.2

Relative cell constant too small

Determined relative cell constant
must not be < 0.8

Solution in incorrect range

Incorrect reference solution, way beyond
the tolerance

Incorrect temperature

Reference solution outside the permissible tem-
perature (0.0 to 34.0°C, or 0.0 to 27.0°C with
reference solution 111.8 mS/cm)

All manuals and user guides at all-guides.com

Содержание 202710/30













































Результаты поиска

Содержание 202710/30

Отзывы:

Похожие инструкции для 202710/30

Бренды по названию

Популярные бренды

JUMO 202710/30, Руководство по эксплуатации

Результаты поиска

Содержание 202710/30

Отзывы:

Похожие инструкции для 202710/30

Бренды по названию

Популярные бренды