manualshive.com logo in svg

Julabo CORIO CP, Руководство по эксплуатации, Страница: 57 / 72

Поделиться
Скачать
Julabo CORIO CP Скачать руководство пользователя страница 57

Maintenance 

57

 

9.6  Clean device 

 

The circulator and bath tank, and also a cooling machine if connected, should 
be cleaned from time to time. 
In addition to this, the device must be appropriately decontaminated if 
hazardous substances have been spilled on or into the device. 
 

 

  Lint-free cloth 

 

  Mild cleaning agent 

 

 

 

  The device is switched off and disconnected from the mains voltage. 

1.  Allow the device to cool down to room temperature. 
2.  Completely drain the bath fluid. 
3.  Clean the surface of the circulator and the bath tank with a damp cloth. 

  Some dish detergent may also be used for cleaning. If in doubt, ask 

technical service for alternative cleaning mediums. 

  The device has now been cleaned. 

 

 

9.7  Device storage 

 

This section describes how to store the device. 
 

 

  The device is switched off and disconnected from the mains voltage. 

1.  Empty all system components completely. 
2.  Clean the device. 
3.  Carefully dry the device and all its system components, e.g. with 

compressed air. 

4.  Close all connections. 
5.  Store the device in a dust-free, dry and frost-free location. 

  The device is protected and can be safely stored there. It can be put into 

operation again as needed. 

 

 

 

 

Содержание CORIO CP









































































Отзывы:

Нет отзывов