JUKI MEB-3200 Series, Инструкция по эксплуатации

Страница: 83 / 520

69
ENGLISH
Setting
range
0 to 1
0 to 80
0 to 80
0 to 1
0 to 1
0 to 1
0 to 1
0 to 1
0 to 1
0 to 64
0 to 1
− 100 to 300
− 100 to 300
− 100 to 300
−
100 to 300
−
100 to 300
−
100 to 300
− 100 to 300
− 100 to 300
− 100 to 300
−
100 to 300
50 to 500
0 to 300
80 to 300
0 to 1
0 to 99
0 to 50
0 to 1
0 to 3,000
Function
Start Sw
One-touch starting selection
With/without
Function key F1
Data No. setting
Function F2 key
Data No. setting
With/without setting of thread tension
compensation value
With/without
Selection of data setting prohibition
Permitted/prohibited
Looper thread trimming control
Presser comes down when returning to set
position
Temporary stop of cut-after knife
Straight bar and cloth open
Front set position
Knife pressing amount data setting accepted
Knife pressing amount (Knife holder No.1)
Knife pressing amount (Knife holder No.2)
Knife pressing amount (Knife holder No.3)
Knife pressing amount (Knife holder No.4)
Knife pressing amount (Knife holder No.5)
Knife pressing amount (Knife holder No.6)
Knife pressing amount (Knife holder No.7)
Knife pressing amount (Knife holder No.8)
Knife pressing amount (Knife holder No.9)
Knife pressing amount (Knife holder No.0)
Knife lower stop time
Number of low speed pulses to lower knife
motor
Number of low speed pulses to lift knife motor
With/without needle thread clamp
Number of stitches to open needle thread
clamp
Needle thread clamp travelling amount
Needle thread draw-in 2-stage operation
Lengthwise speed at the time of needle
thread clamp
Description
Whether starting by start switch only is possible is selected.
0 : Presser comes down by presser switch, the machine
is started by start switch
1 : Presser comes down by start switch and the machine
starts (Presser switch is operative as well.)
Data Nos. which are aassigned to Function F1 key are set.
(Initial value ... Knife position compensation)
Data Nos. which are assigned to Function F2 key are set.
(Initial value ... Copy destination No.)
Whether to set thread tension compensation value with
NEEDLE/LOOPER key is selected.
0 : Without setting
1 : With setting
Whether to prohibit data setting is selected.
0 : Permitted
1 : Prohibited (Thread tension is possible.)
With/without looper thread trimming operation is set.
0 : Without
1 : With
Whether presser returns to set position while it is lowered
after sewing is selected.
0 : Presser goes up and returns to set position.
1 : Presser returns to set position while it is lowered and goes up.
Whether to automatically stop temporarily before
operation of cut-after knife and to make the knife operate
by start switch is selected.
0 : Normal operation
1 : Cut-after knife automatically stops temporarily before
operation and is operated by start switch.
Whether to perform sewing with the cloth open mechanism
opened in case of the pattern in which straight bar is set.
0 : Normal operation
1 : Setting cloth with cloth open mechanism opened
Position from the origin is set when “front” is selected with
memory switch No. 11.
Whether knife holder No. to which knife pressing amount
has been set is set to pattern data is selected.
0 : Without (Knife holder No.0 fi xed)
1 : With (Knife holer Nos.0 to 9 set)
Knife pressing amount of knife holder No.1
Knife pressing amount of knife holder No.2
Knife pressing amount of knife holder No.3
Knife pressing amount of knife holder No.4
Knife pressing amount of knife holder No.5
Knife pressing amount of knife holder No.6
Knife pressing amount of knife holder No.7
Knife pressing amount of knife holder No.8
Knife pressing amount of knife holder No.9
Knife pressing amount of knife holder No.0
Period of time of stopping at the lower position of knife
Cutting speed section at the time of cloth cutting (Down)
Cutting speed section at the time of cloth cutting (UP)
With/without needle thread clamp operation is set.
0 : Without
1 : With
Number of stitches at sewing start to open needle thread
clamp is set.
Setting of travelling amount by mm from end of sewing to
close thread clamp
0 : 1-stage operation
1 : 2-stage operation
Lengthwise jump feed speed from end of sewing to
needle thread clamp
Setting
unit
-
-
-
-
-
-
-
-
-
1 mm
-
1
1
1
1
1
1
1
1
1
1
10 ms
Pulse
Pulse
-
1 stitch
1mm
–
1
pulse/sec.
Initial
value
0
8
0
0
0
1
0
0
0
22
0
0
0
0
0
0
0
0
0
0
30
50
60
80
0/1
5
23/14
0/1
1,000/1,500
No.
14
17
18
19
20
22
23
24
26
29
40
41
42
43
44
45
46
47
48
49
50
55
57
58
65
66
69
B8
C0
＊
H9 through L9 are displayed as well. However, they are the memory switches for the multicutting device.
For the sewing machine not provided with the multicutting device, they are not effective even when the setting
is changed.