background image

JUDO i-soft TGA 4

5

About these operating instructions

1

About these operating in-

structions

These operating instructions must always
be available at the place of use of the water
softening system.
These operating instructions should simplify
getting to know your water softening system
and inform you of its intended applications.
The operating instructions contain important
information pertaining to safe, proper and ef-
ficient operation of the water softening sys-
tem. They contain basic information that
must be observed during installation, opera-
tion and servicing. Observance of this infor-
mation will help to avoid dangers, reduce re-
pair costs and increase the reliability and
service life of the water softening system.
The operating instructions must be read by
each person charged with working on the
water softening system, e.g. for:

– Installation
– Operation
– Servicing 

(maintenance, inspection, servicing)

Installation and servicing must only be per-
formed by personnel who have been author-
ised by the manufacturer to do so, i.e. who
are able to fulfil the instructions referred to in
the installation and operating instructions as
well as country-specific regulations.
Alongside the operating instructions and the
legal regulations applicable in the country
and place of use in respect of accident pre-
vention, the recognised technical regula-
tions for safe and professional work must be
observed.
Therefore, these operating instructions must
be read by the installer and the responsible
technical personnel/operators prior to instal-
lation, commissioning and servicing.

Not only must the general safety instruc-
tions listed in chapter “Intended use” be
observed, but also the specific safety in-
structions that are included under the
other main points.

1.1

Symbols used

The safety instructions contained in these
operating instructions are labelled with the
following symbols:

Instructions attached directly to the rotary
flange fitting or the water softening system,
such as: 
– Direction of flow
– Type label
– Cleaning information 
must be observed without fail and main-
tained so that they are always legible.

NOTICE

Indication of 
existing dan-
gers

Warning of electric voltage

Torques specified by the manu-
facturer

User tips and other information

Содержание 8204016





































Отзывы: