Judo 8165020 Скачать руководство пользователя страница 14

Operation

Before carrying out a backwash,

ensure that the wastewater con-

nection is functional.
At the end of the backwashing

process, turn the handwheel until

it engages so that no more back-

wash water escapes. Otherwise,

water may constantly escape and

cause water damage.

1.

Turn handwheel counter-clockwise up to

stop. 

Backwashing water escapes.

2.

Turn handwheel clockwise up to stop.

Ensure that no water escapes.

The backwashing process is completed

(see chapter 4.2).

4.3

Conversions, changes

WARNING

Unauthorised conversions and

changes are forbidden for safety

reasons. These can impair the

functioning of the device, leading

to leaks and, in the worse case

scenario, to bursting of the device.

In the event of repairs, printed test marks

only remain valid when original spare parts

are used.

4.4

Maintenance, repair,

spare parts

WARNING

The device may only be repaired

by qualified technical personnel.
Only use original spare parts for

repairs.
Before performing work on the

device that goes beyond pure

operational use, the device

must be depressurised! If this is

ignored, the result may be uncon-

trolled egress of water result-

ing in water damage to the build-

ing/home.

4.4.1 Checking the backflow pre-

venter

WARNING

A defective backflow preventer

must be replaced immediately.
The backflow preventer may only

be replaced by trained technical

personnel.

The inlet pressure gauge is used to check

the function of the backflow preventer

(0 - 16 bar).

1.

Close the stopcock or shut-off valve

upstream of the device.

2.

Remove the pre-pressure gauge. 

After a few seconds, no more water

may escape from the pressure gauge

connection.

3.

Install the pre-pressure gauge again.

4.

Open the stopcock or shut-off valve

upstream of the domestic water station

again.

4.5

Temporary removal of the

device

WARNING
If the device is removed due to an

interruption of operation:

Protect the flange surfaces

against damage to ensure proper

sealing.

Protect the device from dirt so

as not to impair drinking water

hygiene.

Store the device in a frost-free

place to prevent damage caused

by freezing water and leakage.

14

JUDO JPM-QC  

1703301 • 2020/07

Содержание 8165020

























Отзывы: