manualshive.com logo in svg

JRC Alphatron Marine Rudder Feedback Unit HD, Инструкция по установке и эксплуатации

Поделиться
Скачать
JRC Alphatron Marine Rudder Feedback Unit HD Скачать руководство пользователя страница 14

14  |  Installation Instructions

Figure 8: Compression Spring

After adjusting, nuts (11) and (12) must be secured, see Figure 7: Stud Bolt on page 13.

1.1.4 Module Electric Connections

The Rudder Feedback Unit needs to be opened to connect the wires, see Opening Rudder Feedback Unit MD on page
14 and Opening Rudder Feedback Unit HD on page 16.

For electric connections, see Figure 19: Connection Diagram Rudder Feedback Unit MD on page 28 and Figure 20:
Connection Diagram Rudder Feedback Unit HD on page 29.

1.1.4.1 Opening Rudder Feedback Unit MD

The Rudder Feedback Unit MD needs to be opened to connect the wires.

1. Remove the four outer screws on top of the Rudder Feedback Unit MD, see Figure 9: Rudder Feedback Unit MD

Four Outer Screws on page 14.

INFO:

Figure 9: Rudder Feedback Unit MD Four Outer Screws

2. Gently remove the top part of the Rudder Feedback Unit MD.

Содержание Alphatron Marine Rudder Feedback Unit HD



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды