JR ProPo C.O.L.T. Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 82

background image

65

System List

ᴾ

▋

Wing Type【WING TYPE】

▋

Function Explanation

Here the wing type can be set. Dual ailerons and dual ﬂaps, dual elevators, dual rudders, tailless
planes, and V-tail wings can be selected.

▋

Setting Method

This function is used to select the Wing type according to the type of airplane.

▋

For Airplane

Wing Type (WING)

Select the Main Wing Type.

Normal (NORMAL)

For standard airplane wing layouts.

Flaperon (FLAPERON)

For wings with Dual Ailerons. Also, mixing Dual Ailerons as Flaps is
possible.
The following channel outputs are used:

Refer to the Page 34 "Flap System【FLAP SYSTEM】"

Channel 2 (AILE)

: Right Aileron (RAIL)

Channel 6 (FLAP)

: Left Aileron (LAIL)

Delta (DELTA)

It is possible to set up a Delta Wing to use Elevons.
The following channel outputs are used:
Channel 2 (AILE)

: Left Elevon (LEVN)

Channel 3 (ELEV)

: Right Elevon (REVN)

The actual meaning of “DELTA” is a deﬁned wing shape, and not a
tailless airplane. However, JR does call tailless airplanes deltas (e.g.
the F-102 or Dassault Mirage III).

V-Tail (V-TAIL)

Used to perform mixing for a V-tail airplane.
The following channel outputs are used:
Channel 3 (ELEV) : Left Tail (LTAL)
Channel 4 (RUDD) : Right Tail (RTAL)

▋

Caution Note

Actually operate the servos and carefully conﬁrm the settings before

ﬂying.

Upon setting the Wing type, the following functions have changes to

the servo naming on the display:
• Travel adjust【TRAVEL ADJUST】・・・・ Page 21
• Sub Trim【SUB TRIM】・・・・・・・・ Page 22
• Reverse Switch【REVERSE SW】・・・・ Page 23
• Servo Monitor【MONITOR】・・・・・・ Page 46
• Fail safe【FAIL SAFE】・・・・・・・・・ Page 61

Airplane

Glider

Normal

Wing Type Selection

V-Tail

Normal / V-Tail

Flaperon / V-Tail

Delta

Flaperon

«
...
64
65
66
67
68
...
»

Содержание C.O.L.T.



















































































Отзывы:

Нет отзывов

Похожие инструкции для C.O.L.T.

Бренд: Camille Bauer Страницы: 30

Бренд: Solartron Metrology Страницы: 25

Бренд: K-PO Страницы: 17

Бренд: Microcyber Страницы: 23

Бренд: Landmark Страницы: 2

Easywave RTM08 Series

Бренд: Eldat Страницы: 2

Kotron RF 2-Wire Series

Бренд: Magnetrol Страницы: 12

Бренд: Vaisala Страницы: 16

Бренд: Icom Страницы: 89

2004-6191-1100-001

Бренд: S+S Regeltechnik Страницы: 32

Бренд: Jobsite Страницы: 2

Бренд: ABB Страницы: 32

Бренд: ABB Страницы: 84

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 72

Platinum standard Series

Бренд: ABB Страницы: 122

Бренд: ABB Страницы: 24

Бренд: ABB Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды