JR ProPo C.O.L.T. Скачать руководство пользователя страница 56

Страница: 56 / 82

Software version (SOFTWARE VER)

This indicates the current version of the
transmitter's software.
For example: 0001-0000 (Ver1.0)

Stick Calibration (STICK CALIBRATION)

This function calibrates the neutral position of the stick and stick travel which is especially useful after changing
Stick mode ( Mode 1 to Mode 2 or Vice Versa). The calibration procedure is as follows.

Place both right and left sticks in their center positions, and set the cursor to "SET", and press the dial to calibrate
neutral.

Next move both right and left sticks up and down and right to left and press the dial to calibrate stick travel.

Be sure to check control movement and neutral positions on the servo monitor screen

Refer to the Page 46 "Servo Monitor【MONITOR】"

▋

Caution Note

Be careful not to force the stick gimbal during the calibration procedure.

Stick Calibration

Software Version

Stick position

Neutral setting

Setting boundaries of

stick movement

System List

Содержание C.O.L.T.



















































































Результаты поиска

Содержание C.O.L.T.

Отзывы:

Похожие инструкции для C.O.L.T.

Бренды по названию

Популярные бренды

JR ProPo C.O.L.T., Руководство по эксплуатации

Результаты поиска

Содержание C.O.L.T.

Отзывы:

Похожие инструкции для C.O.L.T.

Бренды по названию

Популярные бренды