1.
Please read the Instruction Manual carefully before using the machine. Nurses (and other pet care
workers) should be trained to operate the machine under the guidance of qualified medical care personnel
who are familiar with the functions and understand the risks and advantages of
the machine.
2.
Please count the parts and spare parts when unpacking, and read the Instruction Manual carefully.
3.
The equipment shall be placed in a clean place with limited changes in temperature and humidity, protected
from direct sunlight and away from heat radiation.
4.
To ensure the proper operation of the Pet ICU, please fill the bottle with distilled water or purified water.
5.
After the machine is turned on, please preset the temperature value, and warm it up for 3-5 minutes before
use.
Do not use tap water.
6.
Please do not load weight o
n top of
the machine, and the maximum load capacity of the machine housing is
1-2 kilograms (2.2 to 4.45lbs).
7
.
The machine is equipped with an intelligent alarm system sensor for five faults; extreme temperature,
excessive moisture, indoor
oxygen
concentration, lack-of-water in the tank and power supply Interrup-tion.
This alarm system is tested and proven to be safe and reliable. If the machine fails, please inspect the
systems immediately to find out reasons and eliminate the faults. If the faults cannot be eliminated in a
short time, please stop medical treatment or care for pets, and ask for professionals or personnel from the
JorVet
Company to repair the machine.
8. A
llow for the machine to have proper ventilation. Do not block the air outlet and return air inlet.
9.
After being powered on, if the machine is not used, in order to ensure safety and energy-saving,
please
turn the switch to off position and allow for sufficient power down before turning the switch back to on
position.
10.
Do not use alcohol or other organic solvents to wipe the thermostat cover of the tank. Keep it
moisture
free.
11.
The nebulizer should be unplugged as soon as the nebulization is over.
12.
When the LAC alarm can be seen on the humidity display panel, the tank inside should be filled to the
maximum level even if the tank has water half of the maximum level.
1. Provides bacteria free and thermostatic incubation cocoon for young pets.
2. Allows for body temperature recovery, fluid infusion, atomization treatment, incubation, health
improving and comfortable, stable stay in the hospital (for observation for sick, dying and weak pets).
Built-in humidifier bottle: some parts of medical atomizer and the tank are separately packed. Please
pay attention not to damage or miss any parts or spare parts when unpacking.
JorVet J1550 ICU Unit
cabinet
Nebulizer
Power
cord
Waste tray
Water purification filter material (Phosphorus-silicon crystal) User Manual
External Humidifier (optional)
As shown in Figure 4.2.1, the Humidifier Vessel is installed in the right control chamber of the
JorVet
J1550 ICU Unit
. As shown in Figure 4.2.2, open the outlet cover, take out the built-in Water Vessel, fill
the built-in Water Vessel with water, (
using
distilled water or purified water)as shown In Figure 4.2.2.
And then put back the vessel and place the cover in the proper position.
Notes:
a) The Humidifier and Water Level Sensor should be placed securely onto the vessel to prevent the
spill of water.
b) Do not fill the vessel with purified or distilled water, which may cause the malfunction of the Water
Level Control of the water tank and may eventually cause water to spill or leak.
c) The water level should not be above the Highest Level Line (HLV).
d) The purpose of the water purification filter material is to remove hard water scale and improve the
water quality. The validity period of each placement is 10-12 months. Colorless, tasteless and non-tox-
ic, the filter material meets the National Sanitary Standard for Drinking Water& GB1499- 1988 and can
effectively improve water quality.
2. Installation of Humidifier Vessel
Outlet Cover
Humidifier
Water Level
Sensor
Highest Level
of Vessel
Water Vessel
Figure 4.2.1
Figure 4.2.2
02
03
Summary of Important Notes
Product Use
Product Installation
The external Nebulizer can be installed on the left
side of
JorVet J1550 ICU Unit
. Insert the power plug
into the socket on ICU; insert the nozzle of
Nebulizer into the port on the left side as showed in
Figure 9.1.1.
Before nebulization, switch on the nebulizer by
pressing the switch on the nebulizer and then turn
to the operation panel of ICU.
3. Nebulizer Installa�on
Figure 9.1.1
