EN
FR ES JP
13 Using the Rear Bench Seat
• Push the bench seat to its most rearward position.
NOTE:
There are webbing straps attached to the bottom of the rear seat pad. These straps will lock the seat into the most rearward
position. To lock the seat, pull the straps from EACH side of the pad and loop them around the frame as shown, then snap them together.
See Figure 13.1.
• To slide the seat forward, undo EACH snap and reattach the webbing to the underside of the seat pad using the Velcro® attachments.
• Position the canopy to its most forward position.
• To unlatch the buckle press the center button and remove both latch posts.
• Have the child sit on the bench seat facing backward with their feet on the platform.
• You may need to adjust the recline position of the seat to allow for more room for the child to sit.
• Place the crotch strap between the child’s legs.
• Push the waist latch posts into the crotch buckle until all parts snap into place.
See Figure 13.2.
• Adjust the seat belt to be snug around the child’s waist.
• Be sure that BOTH of the child’s feet are fully on the platform at all times.
• Be sure that BOTH of the child’s hands are holding the stroller frame.
!
WARNING
NEVER allow a rear seated child to use the canopy as a hand hold.
14 Storage Basket
The maximum weight that can be carried in the storage basket is 5 lbs (2.27 kg).
15 Seatback Positioning
The seat back can be adjusted to any position from fully upright to reclining. This seat should only be used for a child that is at least 6
months old.
• To recline the seat, release the adjustment lock tab from its locked position by pulling it away from the seat back. Continue to pull this lock
tab downward to adjust the seat back to the desired position, then re-engage the lock tab.
See Figure 15.1.
• To adjust the seat back to a more upright position, release the adjustment lock tab from its locked position. Then simply pull up on the
adjustment strap ring until the seat back is in the desired position and re-engage the lock tab.
See Figure 15.2.
!
WARNING
Whether the seatback is upright or reclined, ALWAYS make certain that the recline mechanism is engaged before
placing the child into the seat.
16 Removing the Caboose Rear Seat
• Unsnap the waist and shoulder straps from the crotch strap.
• Unwrap the left and right armrests of the Caboose Rear Seat from around the upper horizontal frame (on each side). Unsnap both snaps
on each side.
See Figure 16.1.
• Near the front sides of the Caboose Rear Seat are 2 Velcro® straps (one on each side). Pull these straps apart. Repeat on the other side.
See Figure 16.2.
• Locate the 2 long straps on the lower rear of the Caboose Rear Seat. Unbuckle the straps and unwrap each strap from around the outside
of the stroller handle bar by feeding them through the loops on the back of the seat.
See Figure 16.3.
• Locate the straps on the upper rear of the Caboose Rear Seat (two on each side). Unwrap them from the pegs.
See Figure 16.4.
• Push the rear seat crotch strap buckle through the slot in the Caboose Rear Seat (
See Figure 16.5
) and pull the Caboose Rear Seat off of
the rear bench.
17 Installing the Rear Bench Seat Waist Strap
• Remove the rear bench waist strap from the front seat back pocket.
• To install the rear bench waist strap, locate one end of the waist strap where it has a metal D-ring at the end.
• Wrap the strap around the front seat rear tube. Slide the strap through the small opening of the metal D-ring and pull the strap to secure it
to the tube. Repeat for the other end of the strap.
See Figure 17.1.
18 Attaching the Caboose Rear Seat
• Place the seat fabric in position over the sliding rear bench seat so that the seat is facing toward the front of the stroller.
NOTE:
It is not necessary to remove the existing fabric pad from the bench seat.
• Push the rear seat crotch buckle up through the slot in the Caboose Rear Seat.
See Figure 18.1.
• Place the Velcro® strap of the Caboose Rear Seat over the top peg on the respective side of the stroller and wrap the Velcro® strap
around the frame.
See Figure 18.2.
• Wrap the cloth strap over the Velcro strap so that the Velcro® attaches. Secure the peg through the button hole.
See Figure 18.3.
• Wrap the bottom strap around the frame and secure the bottom peg through the button hole.
See Figure 18.4.
• Repeat for the two straps on the other side.
