JOLLY ROGER AMUSEMENT RIDES
Ride flasher options
4.12 SW4 selects the ride flasher options (if fitted).
NOTE
S4 is used to select “Program Mode” and under normal operating conditions is not to be used and must
be set to the OFF position. “Program Mode” should only be used by experienced operators familiar with
the extended programming sequence, or under direct instruction from Jolly Roger (Amusement Rides)
Ltd., or Stamar Electronics.
Volume adjustment
4.13 Access to the volume control knob is gained by removing the coin mechanism (para 4.3 or 4.4)
and is adjusted by turning the control knob on the timer which is located on the back wall of the compartment.
Access to other components
4.14 Access to the 0.4KW VAT 20 inverter, reed sensor actuator and other components on the bottom
frame is gained by removing the access panel (see Fig 7). Turn the base to align access panel opening
with the required component. Access to components installed on the top frame can be acheived in the
same manner.
Drive belts adjustment
NOTE
The drive belts should run tight.
4.15 The “drive belts” are adjusted by loosening the two stop bolts with locknuts and the four bolt
assemblies holding the motor/gearbox assembly to the bottom frame.
4.16 Slide the whole assembly to adjust the belt tension using the two stop bolts with locknuts, finally
tighten the four bolt assemblies and the two stop bolt locknuts.
4.17 The “drive belts” are correctly tensioned during manufacture and should not require adjustment.
Bearings
4.18 All bearings are greased for life and should normally not be re-packed with grease. However, in
certain circumstances the bearings may require lubrication. If this situation arises, apply grease sparingly.
Page 13
4
W
S
1
S
2
S
3
S
4
S
t
u
p
t
u
o
r
e
h
s
a
l
f
l
e
n
n
a
h
C
1
f
f
O
f
f
O
x
F
F
O
s
t
u
p
t
u
o
r
e
h
s
a
l
f
g
n
i
n
n
u
r
l
e
n
n
a
h
C
2
n
O
f
f
O
x
F
F
O
s
t
u
p
t
u
o
r
e
h
s
a
l
f
g
n
i
n
n
u
r
l
e
n
n
a
h
C
3
f
f
O
n
O
x
F
F
O
s
t
u
p
t
u
o
r
e
h
s
a
l
f
g
n
i
n
n
u
r
l
e
n
n
a
h
C
4
n
O
n
O
x
F
F
O
d
e
e
p
s
r
e
h
s
a
l
f
d
r
a
d
n
a
t
S
x
x
f
f
O
F
F
O
d
e
e
p
s
r
e
h
s
a
l
f
t
s
a
F
x
x
n
O
F
F
O
Содержание INTERNATIONAL SPEEDWAY CAR CAROUSEL
