background image

TEC22x6(H)-4 and TEC22x6H-4+PIR Series L

ON

W

ORKS

® Network Thermostat

Controllers with Dehumidification Capability, Fan Control, and Occupancy Sensing

Capability Installation Instructions

1

Applications

The TEC22x6(H)-4 and TEC22x6H-4+PIR Series 
Thermostat Controllers are L

ON

W

ORKS

® network 

devices that provide control of two- or four-pipe fan 
coils, cabinet unit heaters, or other equipment using 
on/off, floating, or proportional 0 to 10 VDC control 
input, dehumidification capability, and up to three 
speeds of fan control. The TEC22x6H-4+PIR Series 
Thermostat Controllers have occupancy sensing 
capability built into the device. These devices maximize 
up to 30% energy savings in high-energy usage light 
commercial buildings, such as schools and hotels, 
during occupied times by using additional standby 
setpoints. See the 

Occupancy Sensor Operation – 

TEC22x6H-4+PIR Series Thermostat Controllers

 

section for more information.

The technologically advanced TEC22x6(H)-4 and 
TEC22x6H-4+PIR Series Thermostat Controllers 
feature a Building Automation System (BAS) 
L

ON

W

ORKS

 network communication capability that 

enables remote monitoring and programming for 
efficient space temperature control. Specific models 
are available to accommodate commercial and 
hospitality applications.

The TEC22x6(H)-4 and TEC22x6H-4+PIR Series 
Thermostat Controllers feature an intuitive User 
Interface (UI) with backlit display that makes setup and 
operation quick and easy. The thermostats also employ 
a unique, Proportional-Integral (PI) time-proportioning 
algorithm that virtually eliminates temperature offset 
associated with traditional, differential-based 
thermostats. 

North American Emissions Compliance

United States

Canada

Installation

Location Considerations

Locate the TEC22x6(H)-4 or TEC22x6H-4+PIR Series 
Thermostat Controller:

on a partitioning wall, approximately 5 ft (1.5 m) 
above the floor in a location of average 
temperature

away from direct sunlight, radiant heat, outside 
walls, behind doors, air discharge grills, stairwells, 
or outside doors

away from steam or water pipes, warm air stacks, 
unconditioned areas (not heated or cooled), or 
sources of electrical interference

For integrated Passive Infrared (PIR) models, make 
sure the thermostat controller is located centrally, 
where occupant movement is frequent.

IMPORTANT:

The TEC22x6(H)-4 and 

TEC22x6H-4+PIR Series Thermostat Controllers 
are intended to provide an input to equipment under 
normal operating conditions. Where failure or 
malfunction of the thermostat controller could lead to 
personal injury or property damage to the controlled 
equipment or other property, additional precautions 
must be designed into the control system. 
Incorporate and maintain other devices, such as 
supervisory or alarm systems or safety or limit 
controls, intended to warn of or protect against 
failure or malfunction of the thermostat. 

This equipment has been tested and found to 
comply with the limits for a Class A digital device 
pursuant to Part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection 
against harmful interference when this equipment is 
operated in a commercial environment. This 
equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause 
harmful interference to radio communications. 
Operation of this equipment in a residential area is 
likely to cause harmful interference, in which case 
the user will be required to correct the interference 
at his/her own expense.

This Class (A) digital apparatus meets all the 
requirements of the Canadian Interference-Causing 
Equipment Regulations.

Cet appareil numérique de la Classe (A) respecte 
toutes les exigences du Règlement sur le matériel 
brouilleur du Canada.

TEC22x6(H)-4 and TEC22x6H-4+PIR Series L

ON

W

ORKS

® Network 

Thermostat Controllers with Dehumidification Capability, Fan Control, 
and Occupancy Sensing Capability

Installation Instructions

Part No. 24-9890-1249, Rev. —

Issued February 8, 2010

Содержание TEC2216-4

























Отзывы: