Johnson Controls MP-802 P9M0 Скачать руководство пользователя

Страница: 5 / 22

D-308439 MP-802 PG+ Rev.0

Table 1: Configuration options

Option

Action

FREEZING < 7°C [<45°F]

Define whether or not the control panel will report a freezer

alert when the temperature drops below the threshold value

for at least the

Alert Delay

duration. Alert restore will occur

when the temperature rises

1°C

(1.8°F)

above the threshold

for at least the

Restore Delay

duration.

Note:

The default threshold value for freezing is

7°C

(45°F).

Optional settings: See Configuring the Temperature Alerts.

FREEZER > -

10°C [<14°F

Define whether or not the control panel will report a freezer

alert when the temperature rises above the threshold value

for at least the

Alert Delay

duration. Alert restore will occur

when the temperature drops 1

°C

(1.8

°F)

below threshold for

at least the

Restore Delay

duration.

Note:

The default threshold value for freezer is -

10°C

(14°F).

Optional settings: See Configuring the Temperature Alerts.

MP-802 PG+ Wireless PIR Motion Detector Installation Guide

Содержание MP-802 P9M0























Результаты поиска

Содержание MP-802 P9M0

Отзывы:

Похожие инструкции для MP-802 P9M0

Бренды по названию

Популярные бренды

Johnson Controls MP-802 P9M0, Руководство по установке

Результаты поиска

Содержание MP-802 P9M0

Отзывы:

Похожие инструкции для MP-802 P9M0

Бренды по названию

Популярные бренды