Johnson Controls JRE Series Скачать руководство пользователя страница 4

W A T E R - S O U R C E   H E A T   P U M P S

JRE-Series

R e v. :   A u g u s t   1 9 ,   2 0 2 0

I n s t a l l a t i o n ,   O p e r a t i o n ,   M a i n t e n a n c e

4

General Information

WARNING! 

To avoid equipment damage, do not use these 

units as a source of heat during the construction process. 

The mechanical components and filters used in these units 

will quickly become clogged with construction dirt and debris 

which may cause system damage.

WARNING! 

Some units may be charged with refrigerants 

other than 410A and are so labeled. Use appropriate 

refrigerant handling techniques. Mixing refrigerants in units 

is dangerous and can cause equipment damage. To avoid 

the release of refrigerant into the atmosphere, the refrigerant 

circuit of this unit must only be serviced by technicians who 

meet local, state and federal proficiency requirements.

5.  Verify curb is proper size for unit. Install curb 

according to manufacturer's instructions prior to 

installing unit.

6.  Properly size supply and return duct work. Mount 

supply air duct to curb before installing unit.

Inspection -

 Upon receipt of shipment at the job site, 

carefully check the shipment against the bill of lading. 

Make sure all units have been received. Inspect the carton 

or crating housing of each Rooftop Unit and inspect each 

unit for damage. Assure that the carrier makes proper 

notation of any shortages or damage on all copies of the 

freight bill and that he completes a Carrier Inspection 

Report. Concealed damage not discovered during 

unloading must be reported to the carrier within 15 days 

of receipt of shipment. 

NOTE: It is the responsibility 

of the purchaser to file all necessary claims with the 

carrier. 

Storage -

 Upon the arrival of  equipment at the job site, 

immediately store units in a clean, dry area. 

Store units 

in an upright position at all times.

 Stack unit model 

numbers JRE-036 through JRE-120 no more than 2 

units high. Do not stack units larger than model number 

JRE-120. 

Do not remove equipment from pallets until 

equipment is required for installation

Unit Protection -

 Cover rooftop units on the job site. 

Cap the open ends of pipes. In areas where painting, 

plastering, roofing, or the spraying of fireproof material 

has not been completed, all due precautions must 

be taken to avoid physical damage to the units and 

contamination by foreign material. 

Physical damage and 

contamination may prevent proper start-up and may 

result in costly equipment cleanup. 

Pre-Installation -

 Installation, operation and maintenance 

instructions are provided with each unit. Before unit start-

up, read all manuals and become familiar with the unit 

and its operation. Thoroughly check out the system before 

operation.

Prepare rooftop units for installation as follows:
1.  Compare the electrical data on the unit nameplate 

with ordering and shipping information to verify that 

the correct unit has been shipped.

2.  Select an installation site on the roof which allows 

adequate clearance for maintenance and servicing 

of the unit. A minimum of two feet of clearance is 

required on all service access and drain connection 

sides of the unit.

3.  Verify that refrigerant tubing is free of kinks or dents, 

and that it has not been damaged during shipping.

4.  Examine all pipes, fittings, valves and components 

before installing the system. Remove any dirt found 

on or in these components and assure that all 

components are securely fitted.

� 

WARNING!

 �

� 

WARNING!

 �

� 

CAUTION!

 �

CAUTION! 

Supply air duct is inaccessible  from inside unit 

once unit is installed.

WARNING! 

The installation of water-source heat pumps and 

all associated components, parts, and accessories which 

make up the installation shall be in accordance with the 

regulations of ALL authorities having jurisdiction and MUST 

conform to all applicable codes. It is the responsibility of 

the installing contractor to determine and comply with ALL 

applicable codes and regulations.

� 

WARNING!

 �

WARNING!

 This product can expose you to chemicals 

including formaldehyde, which is known to the state of 

California to cause cancer. For more information, go to 

www.P65Warnings.ca.gov.

� 

WARNING!

 �

Содержание JRE Series













































Отзывы: