manualshive.com logo in svg

Johnson Controls IOM2723, Руководство по установке, Страница: 16 / 18

Поделиться
Скачать
Johnson Controls IOM2723 Скачать руководство пользователя страница 16

Accessories

See the following table for expansion module

accessories ordering information.

Table 9: Accessories Ordering Information

Product Code Number

Description

Mobile Access Portal (MAP) Gateway

Refer to the 

Mobile Access Portal Gateway Catalog Page (LIT-1900869)

 to identify the

appropriate product for your region.

Note: 

The MAP Gateway serves as a replacement for the BTCVT, which is no longer

available for purchase, but continues to be supported.

TL-CCT-0

Metasys

 Controller Configuration Tool (CCT) Software

MS-FCP-0

Metasys

 Field Controller Firmware Package Files for CCT

TP-2420

Transformer, 120 VAC Primary to 24 VAC secondary, 20 VA, Wall Plug

Y65T31-0

Transformer, 120/208/240 VAC Primary to 24 VAC Secondary, 40 VA, Foot Mount, 8 in.

Primary Leads and Secondary Screw Terminals, Class 2

Note: 

Additional Y6x-x Series transformers are also available. Refer to the 

Series Y63,

Y64, Y65, Y66, and Y69 Transformers Product Bulletin (LIT-125755)

 for more information.

AS-CBLTSTAT

Cable adapter for connection to 8-pin TE-6700 Series sensors

AS-XFR050-0

Power transformer (Class 2, 24 VAC, 50 VA maximum output), no enclosure

AP-TBK4SA-0

Replacement SA Bus Terminal Blocks, 4-Position, Brown, Bulk Pack of 10

AP-TBK4FC-0

Replacement FC Bus Terminal Blocks, 4-Position, Blue, Bulk Pack of 10

AP-TBK3PW-0

Replacement Power Terminal Blocks, 3-Position, Gray, Bulk Pack of 10

IOM2723 Input/Output Module Installation Guide

16

Содержание IOM2723



















Отзывы:

Нет отзывов