background image

description of the physical features and a reference

to further information where required.

Figure 1: IOM2723 Physical Features

Table 1: IOM2723 physical features callouts and

descriptions

Physical feature: description and references

1

Analog Outputs (AOs) Terminal Block (see Table 2)

2

Mounting Clip

3

Device Address DIP Switch Block (see 

Setting the device

address

)

4

24 VAC, Class 2 Supply Power Terminal Block (see 

Supply

power terminal block

)

5

Cover Lift Tab (see 

Removing the expansion module

cover

)

6

Sensor Actuator (SA) Bus/Field Controller (FC) Bus

Terminal Block (see 

SA/FC bus terminal block

)

7

End-of-Line (EOL) Termination Switch (see 

Setting the

End-of-Line (EOL) Switch

)

8

Universal Inputs (UIs) Terminal Block (see Table 2)

9

LED Status Indicators (see Table 8)

Mounting

Observe the following guidelines when mounting an

expansion module:
• Ensure the mounting surface can support the

expansion module, DIN rail, and any user-

supplied enclosure.

• Mount the expansion module horizontally on 35

mm DIN rail whenever possible.

• Mount the expansion module in the proper

mounting position (Figure 2).

• Mount the expansion module on a hard, even

surface whenever possible in wall-mount

applications.

• Use shims or washers to mount the expansion

module securely and evenly on the mounting

surface.

• Mount the expansion module in an area free

of corrosive vapors and observe the Ambient

Conditions requirements in Table 10.

• Provide for sufficient space around the expansion

module for cable and wire connections for easy

cover removal and good ventilation through

the expansion module (50 mm [2 in.] minimum

on the top, bottom, and front of the expansion

module).

• Do not mount the expansion module on surfaces

prone to vibration, such as duct work.

• Do not mount the expansion module in areas

where electromagnetic emissions from other

devices or wiring can interfere with expansion

module communication.

IOM2723 Input/Output Module Installation Guide

2

Содержание IOM2723



















Отзывы: