background image

1-WAY CASSETTE

2-6 

TC-18002

2.7  Operation Space

2.8  Sensible Heat Factor (SHF)

Models:  (H,Y,C)IC1006B21S, (H,Y,C)IC1008B21S, (H,Y,C)IC1012B21S and (H,Y,C)IC1015B21S 

Min.

59-1/16 (1500)

Min.

3-15/16 (100)

Min.

13/16 (20)

Min.

11-13/16 (300)

Piping Side

Distance from Wall 

Unit: inch (mm)

Min. 3-15/16

(100)

Min. 11-13/16

(300)

Unit: inch (mm)

Min.3-15/16

(100

)

Min. 13/16

(20)

< For One Unit Installation >

Min. 94-1/2

(2400)

Floor Level

NOTE:

This figure indicates the minimum service space.

There are no obstacles which may hamper 

incoming and discharged air.

(Unit Height in False Ceiling)

Clearance

Down Slope

Gradient: 1/25 to 1/100

Condensate Piping

9-1/4 (235)

Min. 3/8 (10)

Unit: inch (mm)

Model

SHF*

(H,Y,C)IC1006B21S

0.79

(H,Y,C)IC1008B21S

0.80

(H,Y,C)IC1012B21S

0.83

(H,Y,C)IC1015B21S

0.83

NOTE:

* SHF is based on combinations within the VRF system and the following conditions:

Cooling Operation Conditions

Indoor Air Inlet Temperature:  80

o

F DB  (26.7

o

C DB)

 67

o

F WB (19.4

o

C WB)

Outdoor Air Inlet Temperature:  95

o

F DB  (35.0

o

C DB)

Piping Length: 24 ft. 7-3/16 in. (7.5m)

Piping Lift: 0 ft. (0m)

Содержание CIC1006B21S



















































Отзывы: