background image

1

32

16

15

1

6

2

5

9

10

13

8

7

14

12

4

3

11

Fig. 1

FEATURES

1

Air circulation fan

2

Fuse/s

3

Electronics module (MODAIRFLOW)

4

Spillage monitoring device (TTB) (at rear)

5

Multifunctional control

6

Limit Switch

7

Airflow sensor (Modairflow models)

8

Fan delay control (non modairflow models)

9

Pilot burner

10

Burner and control assembly

11

Data plate

12

Piezo unit

13

Gas connection

14

Electrical assembly

15

Time control

16

Air filter

1.1

HI-SPEC J50 is an open-flued, fan assisted downflow, ducted warm air heater, which may be supplied with MODAIRFLOW
control and in combination with an ELJAN 6 water circulator. A non-MODAIRFLOW version is available as an option.
A Spillage Monitoring Device (TTB) is fitted which senses the temperature in the draught diverter, and shuts down the
appliance when this temperature rises due to the presence of flue gases.

1.2

The air heater output can be adjusted between 11.72kW (42.2MJ/h, 40,000Btu/h) and 14.65kW (57.75MJ/h,  50,000Btu/h).
“Summer air circulation” of unheated air is available by manual selection (see User’s Instructions). ELJAN 6 output is 3.32kW
(11.5MJ/h, 11.340Btu/h).

THIS APPLIANCE CONFORMS TO BS EN 45014

Installation shall be in accordance with the current editions of:
Building Standards (Scotland) (Consolidation) Regulations
Building Regulations
Gas Safety (Installation and Use) Regulations (as amended)
BS 7671 Institute of Electrical Engineers (I.E.E) Wiring Regulations
BS 6891 Installation of Low Pressure Gas Pipework of up to 28mm (R1) in domestic premises (2nd family gases).
BS 5440 Pt. 1 (Flues for Gas Appliances)
BS 5440 Pt. 2 (Air Supply for Gas Appliances)
BS 5864 Installation of Gas Fired Ducted Air Heaters
Model and Local Authority Bye-laws

This appliance has been tested and certified for use with natural gas

1.

BRIEF DESCRIPTION

These instructions are to be left with the User or adjacent to the Gas Meter

Johnson and Starley prides itself on its ability to supply spare parts quickly and efficiently. If you
have a problem in obtaining a spare part, please contact Johnson and Starley Spares Department at
the address below.

JOHNSON & STARLEY LTD.

Telephone:

(01604) 762881

Rhosili Road,

Brackmills,

 Fax: (01604)  767408

  Northampton NN4 7LZ

Publication No. ZZ 851/6

October 2006

HI-SPEC J50 WARM AIR HEATERS

with MODAIRFLOW and non-MODAIRFLOW Control

INSTALLATION, COMMISSIONING & SERVICING INSTRUCTIONS

G.C. No 42 451 13

Содержание HI-SPEC J50

































Отзывы: