Johnson & Starley HI-SPEC J50 Скачать руководство пользователя страница 27

6

27

1.6m

4.6m

H

a

 = 6.2m

Ridge Terminal

2 x 300 mm lengths

4 x 1000 mm lengths

45

O

 bend

45

O

 bend

2 x 300 mm lengths

300 mm length

Flue spigot

100 mm dia flue pipe

Fig. 2

Worked example of equivalent flue height

5.1.12 Where flue blocks are used, builders should ensure that no obstruction is created during erection. The installer should

ensure that the connection flue does not project beyond the internal wall of the flue blocks and that there is provision
for examination and servicing.

5.1.13

Important: 

 Before installing the appliance, carry out a visual check of the flue system as directed in the relevant

section of BS 5440 Pt. 1, then check the flue performance as follows:

a.

Close all doors and windows in the room in which the appliance is to be installed.

b.

Introduce some heat into the flue, using a blow torch or other means.

c.

Carry out a flow visualisation check with a smoke pellet at the intended position for the appliance. Ensure that
there is discharge of smoke from the correct terminal only, and no spillage into the room. Smoke coming out of
other than the correct terminal only, or a down draught or ‘no flow’ condition, indicates that the flue has failed
the test, and the appliance shall not be connected until the defect has been found and rectified, and the test
satisfactorily completed.

10.

SHORT LIST OF SPARES

ITEM G.C.

MAKER’S

DESCRIPTION

QTY

No

No

No

1

382 758

1000-0500725

Fan assembly

1

2

E02-417

B502-0182000

Filter tray assembly

1

3

244  985

CL30-0500000

Time control CL3

1

4

244 986

1000-0000040

Time control cover

1

5

384 739

BOS00105

Overheat (limit Control)

1

Honeywell L4069C

6

393 412

BOS01301

Multifunctional control

1

Honeywell V8600C

7

232 903

BOS02061

Sealing ring (for item 6)

2

8

244 880

BOS02397/4

Pilot assembly

1

9

392 935

1000-0705140

Pilot Injector

1

10

E02-418

1000-0705260

Pilot Feed Pipe

1

11

386-820

1000-0703870

Thermocouple

1

12

386 775

BOS01970

Electrode

1

13

397 819

BOS02394

Electrode lead

1

14

244 898

BOS02406

Electrode Nut

1

15

E02-419

B502-0502000

Spillage Monitoring Device (TTB)

1

16

E02-420

B502-0700000

Burner and Controls Assembly

1

17

E02-421

1000-0705280

Burner and Cross Lighter Assembly

1

18

398-351

1000-0700980

Main Injector Bray Cat 23/600

2

19

E02-422

1000-0705340

Cross Lighting Injector (Bray)

1

or

E02-423

1000-0705310

Cross Lighting Injector (Stereomatic)

1

20

E02-424

B502-0300005

Heat Exchanger exchange kit

1

21

395 945

1000-0700570

Piezo Unit

1

22

244 971

B300-0706000

Igniter Bracket

1

23

244 957

1000-2500010

Rope Ring Seal (for heat exchanger cap)

1

24

245 067

B500-0380005

Draught Diverter Assembly

1

25

E02-425

B502-0161000

Lower Compartment Door

1

MODAIRFLOW MODELS

26

E02-545

B502-0156000

Fan Compartment Door

1

27

245 080

B500-0530005

Control Panel with Transformer

1

28

245 081

1000-0500880

Wiring Harness

1

29

245 191

R005

Electronics Module

1

30

230 496

S00076

Airflow Temperature Sensor

1

31

244 933

1000-0514230

Fuse 1A, (T)

2

32

386 475

BOS01242

Thermista-stat

1

33

E02-433

1000-0516870

Transformer

1

NON-MODAIRFLOW MODELS

34

E02-427

B502-0157000

Fan Compartment Door

1

35

245 040

B500-0500730

Control Panel

1

36

245 045

1000-0500870

Wiring Harness

1

37

385 159

BOS00104

Fan Control Honeywell L4068C

1

38

245-509

1000-0513820

Fuse 3.15A, (T)

1

Содержание HI-SPEC J50

































Отзывы: