manualshive.com logo in svg

John Bean 48109B, Инструкция по установке и эксплуатации

Поделиться
Скачать
John Bean 48109B Скачать руководство пользователя страница 27

27 of 40 

QUARTERLY REAR SLIP PLATE MAINTENANCE 

 

1.

 

Remove top Slip Plate covers by first removing the four (4) shoulder bolts on each cover. 

 

2.

 

Remove polyethylene bearing cages insuring that all the delrin bearings remain in the 
cages.   Additional delrin bearings may be purchased if required. 

 

3.

 

Clean runway surface and touch up any paint wear with a rust resistant paint.   Allow 
paint to dry thoroughly. 

 

4.

 

To obtain optimum performance, the position of the slip plate bearing cage should be 
rotated every quarter to change the wear pattern.   With the first quarter maintenance, flip 
the bearing cage over to the opposite side.   With the second quarter maintenance, rotate 
the bearing cage end-to-end.   With the third quarter maintenance, flip bearing cage over 
to the opposite side.   Fourth quarter maintenance should see the bearing cage rotated 
back to the position it started in. 

 

5.

 

Quarterly maintenance will optimize performance and contribute to longer slip plate life. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание 48109B









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды